20 Most Recent
Ultra Linear UL-1600M Car Audio Amplifier - Page 9 Questions & Answers
Reset button in kd-r426 and how reset
To reset your KD-R426, locate the reset button on the unit. This is usually located behind the faceplate. Once you've found the reset button, press and hold it for about five seconds. After a few seconds, you should see the message "RESET" appear on the display of your stereo. At this point, you can release the reset button.Your KD-R426 should now be reset and working properly. If you have any questions, or if you need help resetting your stereo, please consult your owner's manual or contact a qualified technician
Radio won't turn up. Very low volume out of speakers
It sounds like you are having trouble with the volume on your radio. This could be caused by a few different things. To troubleshoot, first ensure that the volume knob on the radio is turned up to its max. If the volume is already turned up, then you should check the speaker wires to make sure they are connected properly and not loose or frayed. If the wires are secure, then you should check the volume control on your amplifier to make sure it is not set to a low volume level. If the amplifier volume is already set to a high level, then the problem may be with the radio itself and you may need to contact a professional for extra help.
NHDT-W55 display works only reverse mode and there is no sound as well.
It sounds like your NHDT-W55 is having issues with displaying audio and video correctly. This could be caused by a faulty connection between the head unit and the speakers or a faulty wiring connection. To troubleshoot, first check all the connections between the head unit and the speakers to make sure they are securely connected. If the connections are secure, then check the wiring connections to make sure they are not loose or frayed. If the wiring connections are good, then the problem could be with the head unit itself and you may need to contact a professional for further help.
Cage/Holder FM & DAB reception issues
It sounds like you are having trouble with the radio and DAB reception when the head unit is in the cage/holder. This could be caused by either a faulty antenna connection or a faulty ground connection. To troubleshoot, first check the antenna connection to make sure it is securely connected. If the connection is secure, then check the ground connection to make sure it is properly connected to the chassis of your vehicle. If the ground is not connected properly, it can cause signal interference and reception issues. If these steps do not resolve the issue, then you may need to contact a professional for futher help.
891 mini component system will not turn on
If your 891 mini component system is not turning on, there could be a few possible causes for the issue. Here are some steps you can take to troubleshoot the problem:
- Check the power source: Make sure the system is plugged in and that the outlet it is plugged into is functioning properly.
- Check the fuse: If the system is plugged in and the outlet is functioning properly, the issue may be with the fuse. Check the fuse to see if it has blown and replace it if necessary.
- Check the power cord: If the power source and fuse are both functioning properly, the issue may be with the power cord. Check the cord to see if it is properly connected and in good condition. If the cord is damaged, you may need to replace it.
- Check the power switch: If the power source, fuse, and power cord are all functioning properly, the issue may be with the power switch. Check the switch to see if it is functioning properly and test it to see if it is turning the system on and off as expected. If the switch is not functioning properly, you may need to replace it.
Connector of steel
Need Steel Mate subwoofer model no. SW826,power/speaker input cable ASAP
How to reset equaliser?when i turn up the volume the sound has too much bass. I fot JVC RX-5042 audio reciever .
To reset the equalizer settings on a JVC RX-5042 audio receiver, you will need to follow these steps:
- Press the "Menu" button on the receiver.
- Use the arrow buttons to navigate to the "Sound" menu, and then press the "Enter" button.
- Use the arrow buttons to navigate to the "Equalizer" option, and then press the "Enter" button.
- Use the arrow buttons to navigate to the "Reset" option, and then press the "Enter" button.
- Press the "Menu" button to exit the menu and save the changes.
This will reset the equalizer settings to the default values. If you continue to experience issues with the bass level when the volume is turned up, you may need to adjust the equalizer settings manually. To do this, follow the steps above to access the equalizer menu, and then use the arrow buttons to adjust the levels of the different frequency bands (bass, mid, treble, etc.) to your liking.
I hope this helps! If you have any further questions, don't hesitate to ask.
Not finding what you are looking for?