D-Link 802.11g Wireless Router WBR-1310 (WBR1310) - Page 7 - Answered Questions & Fixed issues

Your modem most likely needs to be powered-off for about 15 minutes in order for the NVRAM to clear the MAC address of the device that you previously had connected to it.
Unplug the power cord from the modem and wait about 15 minutes with the power off. After the 15 minutes, connect the router to the modem with the Ethernet cable and plug the power cord of the back in to the modem. One the modem has completed its startup, it should then work with your router.
If this does not work, then you may need to call your ISP to have them remotely clear the old MAC address from the modem so that it will work with your router.

in back side of router you will find small hole for reset, please push that button for 15 second during power on then try to restart router.it will reset to default password.

The WEP encryption key is in your router's wireless settings. Log into your router and got to the wireless settings, you will need to get the SSID and the WEP key. Then go to your computer/laptop's wireless card and configure it with the router's SSID and WEP key, so it will then connect to the wireless router and the Internet.

To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security.

To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1).

Enter the user name (admin) and your password. Leave

the password blank by default.

If you get a Page Cannot be Displayed error, please

refer to the Troubleshooting section for assistance.

The manual:

http://www.scribd.com/doc/4040609/wbr1310-manual-110

Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Go to D-Link - TechSupport FAQ.

If you need more help come back.

Post / thumbs / testimonial are welcome!

yes you can, you need to manually configure settings

Go to Dlink website and download the latest drivers/ firmware for your router. That may fixs the problem

give the this ip to your pc 192.168.0.100 when connect with dlink adaptor with lan cable and sub netmask 255.255.255. (manul ip for connecting)

Just reset it! At the back of the router is a small hole.With a toothpick or some like press gently for 30 seconds and wait for the router to start up again.Log in to http://192.xxx.xxx and start a new configuration.

If you need more help come back.Post / thumbs / testimonial are welcome!

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Click on wireless then wireless security Enable WEP then enter new password save settings and restart router .Then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa

1st you need to configure the the D-Links wireless settings eg, the SSID and encryption, and the configure the wireless card in the computer/laptop with the D-Link's wireless settings so it can connect to the D-Link.
To secure you wireless network from unauthorized access, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security

Hello;
First connect via Ethernet. Then

• Click START'RUN and then type CMD
• At the black window with the prompt(cursor) type ipconfig and search "default gateway"
• Type the gateway address in the browser ej: 192.168.0.1

This is for enter the web administration of the router. I don't know your revision. But I will get you the Hardware Version: A1 Firmware Version: 1.04

• Aim for Status as the picture above

On the WAN section is the actual Internet. WAN = Wide Area Network. Your computer is actually on the LAN = Local Area Network. The Computer looks the address on the router, then the router go to the WAN for the information. But this is transparent to the user. If the WAN is in cero on the addresses, you have to check the installation. when the installation are correct power cycle the modem and the router and try again. Always connected via Ethernet cable. Hope to help!

You don,t need to reset your router password only if you can,t log in the router configuration page.

If you need more help come back.Post / thumbs / testimonial are welcome!

You can reset the router.Here is how!

Step 1: With the unit on, place a paper clip into the hole on the back of the unit labeled Reset.



Step 2: Hold paper clip down for 10 seconds and release.

Note: Do not repower unit during this procedure.

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

Note: The factory defaults username is admin, and there is no password.


If you need more help come back.Post / thumbs / testimonial are welcome!

ome wireless networks based on the 802.11b or 802.11g standards transmit their signal in a narrow radio frequency range of 2.4 GHz. Various other electronic devices in a home, such as cordless phones, garage door openers, baby monitors, and microwave ovens, may use this same frequency range. Any such device can interfere with a Wi-FI home network, slowing down its performance and potentially breaking network connections.
The 2.4 GHz Wi-Fi signal range is divided into a number of smaller bands or "channels," similar to television channels.Many wireless products ship with a default Wi-Fi channel of 6. If encountering interference from other devices within the home, consider changing the channel up or down to avoid it. Some Wi-Fi channel numbers overlap with each other. Channel 1 uses the lowest frequency band and each subsequent channel increases the frequency slightly. Therefore, the further apart two channel numbers are, the less the degree of overlap and likelihood of interference.
If this won't work, Then consider buying a new wireless router as your current is deemed broken.

Step 1 With the unit on, place a paper clip into the hole on the back on the unit labeled Reset.



Step 2 Hold paper clip down for 10 seconds and release.

Note: Do not repower unit during this procedure.

Step 3 The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

Resetting the router does not reset the firmware to an earlier version. It will change all settings back to factory defaults.

Note: The factory defaults username is admin, and there is no password.

If you need more help come back.Post / thumbs / testimonial are welcome!

First you have to access the router through web browser (Internet Explorer) by typing the IP address of your router in the address bar, which is usually 192.168.1.1 or 192.168.0.1 and lookup for the options to do the following: -
1. Change the SSID (Name) of the router
2. Change the default administrative user name and password (unless you've configured otherwise, the default username is admin and the password password.)
(The above step would prevent unauthorized access to your router)

Next step is to secure it:
1.On the left-hand side, under Setup, click "Wireless Settings" 2.Under "Security Options", select your desired encryption method (preferably WPA2-PSK)
3.Choose a Network Key - it can be anything, as long as it's 8-63 characters in length
4. Click Apply

Now your router and your connection would become secure and the user has to provide the network key to access the internet.

Hope this Helps!
CreativeTECH
Feel free to contact me for further assistance

CreativeTECH

WPA is a strong form of wireless encryption, however not all wireless adapters support this feature. If your wireless adapter does not support WPA you will want to use WEP to secure your wireless network.

You can find information on configuring your WBR router for WEP here

Step 1: Open a web browser and type the IP address of the WBR series router into the address bar (default is http://192.168.0.1).

Step 2: The default username is admin (all lower case) and the default password is blank (nothing). Click on OK.

Step 3: Click on the Setup tab at the top and then click on Wireless Settings on the left-hand side.



Step 4: Select the type of WPA encryption you would like to use with your wireless adapter from the Security Mode drop down menu. For WPA-PSK select Enable WPA- Personal Wireless Security (enhanced).

Note: All wireless products on the wireless network must have the same level of security to connect to the network.

Step 5: In the WPA Personal section, configure the following:

• Select the Cipher Type
• Select the PSK or EAP
• Enter your Passphrase
• Re-Enter your Passphrase

Step 6: Click the Save Settings button to save your settings.

If you need more help come back.Post / thumbs / testimonial are welcome!

Yes you can - If you do not know the login and password -
You can reset the D-Link back to the factory defaults by - power off the D-Link, press and hold the RESET button on the back of the router, then power up the router. Hold the RESET button for 5 secs and release the RESET button or until the LEDs flash together.
Connect a LAN cable from the D-Link to the LAN port on your computer and open a browser. Enter the D-Link's configuration URL http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)
You can now configure the wireless settings, eg. SSID and encryption etc.

To secure your wireless network from unauthorized access, please cick on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security.

You can change the wireless name (SSID) and the wireless password by accessing the setup page. To access the setup page, do the following;

Open internet explorer or firefox and type in 192.168.0.1. It will ask for username and password. In the username field, type "Admin" , A in Admin should be a big letter. In the password field , don't type anything. Hit enter in yout keyboard and you will see the set-up page. In the set-up, look at the right side and click Wireless Settings and you will see Wireless Network Name (Also called the SSID) , and change that. Under Wireless Security Mode, change the wireless password or Passphrase.