20 Most Recent Bosch 36 Inch Pyramid Chimney Hood - Black Questions & Answers

Screen is not the correct product to use to bird or squirrel proof the chimney. Your local hardware will have what is known as hardware cloth. It's actually a heavy wire mesh with 1/4" or 1/2" square pattern. you should be able to purchase it, by the foot, off a roll.

Bosch 36 Inch... • Answered on Oct 30, 2014

The fault is the pump pressure is low and must be checked . make sure that in the first place there is no dirt that is clogging the filter in the pump that is causing the drop of pressure in the pump.
So remove the pump and do a good cleaning , use a reverse flushing to take out all dirt.Now make sure that the inlet to the pump is also clean.
Now reset and test the pressure. If the pressure is good then your top spray arm will will rotate and spray.
If not the pump is a suspect and must be checked for perfomance or a replacement is the other option.
Finally make sure that the voltage to the pump is in order.

Bosch 36 Inch... • Answered on Dec 17, 2010

No you did good in ordering a latch ,that is a common issue i find with the bosch d/w, for no apparent reason the latch locks itself with the door open. Look at the door where the male part of the latch goes into the door, you will see that is locked. if you take it apart and manually unlock the latch u stand to break it. Again you did good on ordering the latch.

Bosch 36 Inch... • Answered on Jul 18, 2010

The problem is hard water. Go to www.dishwasherfilter.com. They have a new product out that solves this problem once and for all. It filters the water entering your dishwasher and removes the hard minerals that cause these spots. Very affordable and guaranteed to leave your dishes looking amazing every time.

Bosch 36 Inch... • Answered on Jan 20, 2010

If a DW is not level on the floor then this can stop the latch from connecting and closing door.

Bosch 36 Inch... • Answered on Dec 28, 2009

Make sure the dishwasher is not stuck in some kind of error mode. Make sure the water valve is turned on. Take the bottom front service door off and locate the water valve on the front left bottom of the machine. Make sure there are wires connected to it. If it's still not working, pick up a cheap electrical multimeter. Set it to the resistance setting, and remove the wires from the water valve. Test the resistance across the water valve's terminals. If the resistance is very high, or infinity, the water valve needs to be replaced. If the water valve is ok, turn the dishwasher on and test the voltage across the wires that go to the water valve at a time in the cycle when you know the dishwasher's controller will be trying to let water in. It may be either ac or dc voltage, so try both settings on the meter if you don't get a reading. If no voltage is read across those wires, open up the dishwasher and find the circuit board that the water valve's wires connect to, and make sure they're connected to the board properly. If that still doesn't work, there's a problem with the dishwasher's control board. Look for a square or rectangular blue, gray, black, white box on the circuit board near where the wire plugs in. This is the mechanical switch that turns on the power to the water valve when the computer sends a signal that it wants water. This switch may be jammed up. Try tapping it firmly with screwdriver. If that doesn't work, you can desolder the power switch and solder on a new one. If that doesn't work, you'll need to replace the board or do some advanced work on it.

Bosch 36 Inch... • Answered on Sep 17, 2009

you need to check the water solenoid valve. if you follow the water line coming into the dishwasher you will find the valve(first spot in the water line with two wires coming from it) if you pull the wires off you should see 110 v when it is trying to fill with water if you do then test the valve for continuity.

Bosch 36 Inch... • Answered on May 06, 2009

JiXing Hardware & Mesh Products co.,ltd ,established in 2005, owns two factories in China mainland.
We can supply many kinds of aluminum cooker hood filters,grease filters,,hardware parts,wire shelf,wire and wire mesh.
Our products are sold all over the world , we can assure the good quality with competitive price.
Hope to establish a long-term business relationship with you.

contact info: [email protected]

Bosch 36 Inch... • Answered on Dec 04, 2007

Near your Burner will likely be a metal heater that glows RED HOT next to the gas burner and when the heat is detected the gas is let go to light. A Safety and a way to light the gas. If you look it may glow slightly but needs to glow full bore to light. This is the most common failure. If you get a kit that has Wire Nuts be sure they are Ceramic Wire Nuts due to the heat or the plastic ones will melt off exposing the wires. Good Luck.

Bosch Kitchen... • Answered on Nov 18, 2019

Use digital tester 1st test the power outlet if theres a voltageif OK check the power cord if broken if OK check the fuse using continuity test/setting,

Bosch Kitchen... • Answered on Jul 15, 2019

Don't fiddle with gas - get a technician or increase your fire insurance.

Bosch Kitchen... • Answered on Jan 20, 2019

set oven into self clean wait till it says door locked and on and then cancel cycle after a couple min should unlock if not you may need lock there is no safty latch ther is door removal latch on hinges if these were in hold position the door would not close

Bosch Kitchen... • Answered on Jan 20, 2019

Error 111 means that your oven thinks that it's over heating. Now whether or not the oven is actually overheating or not, this can be caused by either a bad oven sensor or a bad display relay control board. You can't test the board but you can test the sensor. Open the door and remove the 3-4" long thin metal rod attached to the back wall. There are 2 screws holding the sensor on that you can remove and then pull the sensor forward until you can disconnect it. With a multimeter, check the resistance of the sensor at room temperature and it should be about 1080 ohms. If it's not, replace the sensor, otherwise you need to replace your relay board.

Bosch Kitchen... • Answered on Nov 22, 2018

Most ovens have two or more heater elements, have them checked out one could be faulty.

Bosch Kitchen... • Answered on Oct 01, 2018

TURN OFF POWER pull knobs and dials off open oven door look under console remove toex screws in lower console(control panel) the front panel glass will drop out you can know see a metal panel that surface switchs mount too the screws that hold panel are around the edge the screws that hold cooktop down should be able to be seen you do not have to remove the cooktop to replace switches but once the front screws for cooktop are removed the top slides forward and lifts off there will be 1 ground wiire to disconect from cooktop if you do put it back gl

Bosch Kitchen... • Answered on Sep 21, 2018

Not finding what you are looking for?
Kitchen Ranges Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Kitchen Ranges Experts

Cindy Wells

Level 3 Expert

6259 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a Bosch Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Kitchen Ranges

  • Bosch Kitchen Ranges

Most Popular Question

bosch built in dishwasher spray

  • Kitchen Ranges