20 Most Recent HP Broadcom NetXtreme Network Adapter Questions & Answers


In Vista, you can either go to control panel, device manager and right click on it and click "eneble"
or go to control panel > network sharing and set up wireless network connection
or
go to task manager (press and hold ctrl . alt . delete for a couple of seconds), until task manager comes up. Then click on the services tab, scroll down till you see "Plug Play or Plug and Play and make sure it's running. If it's not, right click on it then click "enable"

In XP
Open Network Connections
Right-click Wireless Network Connection, and then click Properties.
On the Wireless Networks tab, do one of the following: •
To enable automatic wireless network configuration, select the Use Windows to configure my wireless network settings check box. This check box is selected by default. For information about what happens when you enable automatic wireless network configuration, see Notes.
To disable automatic wireless network configuration, clear the Use Windows to configure my wireless network settings check box.
To connect to an existing wireless network, do one of the following:
Access point (infrastructure)
To connect to an existing access point (infrastructure) network, under Available networks, click the network name, and then click Configure.
In Wireless Network Properties, specify the wireless network key (Wired Equivalent Privacy) settings, or, if the network key is automatically provided for you (for example, the key is stored on the wireless network adapter given to you by your administrator), select the The key is provided for me automatically check box. If you are unsure about whether a network key is needed or which settings you need to enter, contact your network administrator or the wireless network adapter manufacturer.

Important
If a network does not broadcast its network name, it will not appear under Available networks. To connect to an access point (infrastructure) network that you know is available but that does not appear under Available networks, under Preferred networks, click Add. In Wireless Network Properties, specify the network name (Service Set Identifier) and, if needed, the wireless network key settings.


Computer-to-computer (ad hoc)
To connect to an existing computer-to-computer (ad hoc) network, under Available networks, click the network name, and then click Configure.
In Wireless Network Properties, specify the wireless network key (Wired Equivalent Privacy) settings, or, if the network key is automatically provided for you (for example, the key is stored on the wireless network adapter given to you by your administrator), select the The key is provided for me automatically check box. If you are unsure about whether a network key is needed or which settings you need to enter, contact your network administrator or the wireless network adapter manufacturer.
If you want to connect to a computer-to-computer (ad hoc) network and both computer-to-computer and access point (infrastructure) networks are within range of your computer, click Advanced, and then click Computer-to-computer (ad hoc) networks only.
To configure a new wireless network connection, click Add, and then do the following: •
In Wireless Network Properties, specify the network name (Service Set Identifier) and, if needed, the wireless network key settings.
If the network connection that you are configuring is to a computer-to-computer (ad hoc) network, select the This is a computer-to-computer (ad hoc) network; wireless access points are not used check box.
To change the order in which connection attempts to preferred networks are made, under Preferred networks, click the wireless network that you want to move to a new position on the list, and then click Move up or Move down.
To change the wireless network connection settings for a network that is listed in Preferred networks, click the wireless network for which you want to change settings, click Properties, and then change the settings as needed.
To remove a wireless network from the list of preferred networks, under Preferred networks, click the wireless network that you want to remove, and then click Remove.
To update the list of available networks that are within range of your computer, click Refresh.
To automatically connect to available networks that do not appear in the Preferred networks list, click Advanced, and then select the Automatically connect to non-preferred networks check box.
To open Network Connections, click Start, click Control Panel, click Network and Internet Connections, and then click Network Connections.
When you enable automatic wireless network configuration, you can connect to an existing wireless network, change wireless network connection settings, configure a new wireless network connection, and specify preferred wireless networks. You will be notified when new wireless networks are available. After you select a wireless network, your wireless network adapter will be automatically configured to match the settings of that network, and a network connection attempt will be made.

To configure settings on the Wireless Networks tab, you must be logged on as an administrator, and you must use a wireless network adapter that supports the Wireless Zero Configuration service. If you are unsure whether your wireless network adapter supports the Wireless Zero Configuration service, contact your network administrator or the wireless network adapter manufacturer. For more information about automatic wireless network configuration, see Related Topics.
If you are using third-party wireless networking software, clear the Use Windows to configure my wireless network settings check box.
If you are unable to connect to an existing wireless network and the name of the network that you want to connect to appears under the Preferred networks list, click the preferred network name, and then click Properties. In Wireless Network Properties, review the settings to ensure that they are correct. If you are unsure whether the settings are correct, contact your network administrator or the wireless network adapter manufacturer.
If the Preferred networks list includes both access point (infrastructure) and computer-to-computer (ad hoc) networks, you cannot move a computer-to-computer network to a position in the list that is higher than the position of an access point network.
To provide enhanced security for 802.11 wireless networks and for wired Ethernet networks, IEEE 802.1x authentication is enabled by default. For more information about how to set up 802.1x authentication.
Hope this helps

HP Broadcom... | Answered on Apr 09, 2012


Check the hp website they usually will have all drivers for things that are compatible with an hp computer along with products that they create. If it is not found on there try www.downloads.cnet.com.

HP Broadcom... | Answered on Oct 23, 2010


Your windows are corrupted.
Install new windows for your laptop.

ENJOY...

HP Broadcom... | Answered on Oct 17, 2009


The Broadcom driver maybe corrupted on got uninstalled. Reinstall the Broadcom driver.

HP Broadcom... | Answered on Aug 11, 2009


install from the cd u hv purchased ur lan card

HP Broadcom... | Answered on Jan 31, 2009


Hi,

Restart your computer in safe mode. Press F8 while rebooting. Once in safe mode, go to Start - control Panel - system. Right click on and remove the network card devices (you might see more of them there than you do in normal mode). Then restart the computer.

It should detect the new card and allow you to install the drivers for it. If it still doesn't detect the new NIC card, try powering off the machine. Open the case, and make sure the card is properly seated inside the computer case. Press down on it firmly. Then restart and see if it detects the card.

If it doesn't detect the card, the card might be bad. If you have another card, I'd suggest trying a different one, to see if it recognizes a card that you know is good.

Try these things and let me know how it goes. Thanks.

-Asaph

HP Broadcom... | Answered on Jan 21, 2009


Make sure the light on your cable modem that represents your connection to the computer (it might be marked LAN, Ethernet, or PC) is lit up and isn't flashing. The light will tell you if your network card is properly connected to the cable modem.

If the light isn't on, make sure you've connected the wire to the right port on the cable modem, and try restarting the cable modem by unplugging it, wait 30 seconds, and plug it back in.

If it still doesn't work after that, contact your Internet provider. Their technical support department can help you get it set up.

HP Broadcom... | Answered on Dec 10, 2007


Check with the LG website for support

If you supply details about your laptop and operating system it should be able to help

http://www.lge.com/support/main.jhtml

HP Broadcom... | Answered on Dec 07, 2007


LARRY WHY DON'T YOU POST THE ANSWER LIKE YOU ARE SUPPOSED TO SO THEY KNOW IT WAS ANSWERED

HP Computers &... | Answered on Aug 09, 2020


Larry Ng writes

Jun 19, 2020
Must we beg you what PC? NOR what OS this is.
failure to boot has vast causes.
Do you want them all, ?
Take the PC to any shop get it fixed.
clear to causes.
1: HDD bad, no bad HDD on earth can boot your OS, is that clear? We test this HDD first.
2: A Corrupted unstated OS. endless ways, reload it and cured.

There are more, but I want to keep it simple.

HP Computers &... | Answered on Aug 05, 2020


Follow the online prompts after installing the hp software.

HP Computers &... | Answered on Jul 28, 2020


Clean the registry and remove any virus that may be present.

HP Computers &... | Answered on Jul 24, 2020


11years old 2009, and all need service that old ok?

here are the top fails on this PC, this old, (lots)
all batteries are no good now, even shorted. dead PC.
CCFL back lamp dies next. VGA port works CCFL not.
and packed up in lint, never seen on ever not.

overheating is caused by zero service done.
cleaning is must. ( and also extends the life of ANY PC)
all vents cleaned and all fan blades.
and this RAD photo below.


if not TOO bad even "can-o-air" sold at walfart works.
I call that back blasting all vents.
I use shop air to blast mine out, (via paint reg to 20psi)
dirt6lt1-undefined-undefined-0.jpg

HP Computers &... | Answered on Jul 23, 2020


Instal the motherboard drivers first.

HP Computers &... | Answered on Jun 16, 2020


you can recover lost files from computer with Asoftech Data Recovery program. here's the good guide
http://www.youtube.com/watch?v=vZDCrKzNl6w

HP Computers &... | Answered on Jun 05, 2020


If this issue started with a motherboard error that appeared to be a faulty CMOS battery and then it started incorrectly detecting your memory and now is asking for a password it could be a faulty motherboard. If you are 110% you or anyone else has set a password on that laptop then I would say your motherboard needs to be replaced. It is a difficult process to reset admin passwords on most laptops due to a security chip that will prevent the trick of removing the battery from working. In all honestly if no one has set a password and the motherboard THINKS someone has then even if you reset the password you will still have issues. There is a small chance your CPU or RAM could be defective. But, again going back to it saying you have a password set that was never set. It just yells faulty motherboard unless someone has set a password without you knowing.

HP Computers &... | Answered on May 28, 2020


If you've got working Wi-Fi but your wired ethernet connection is not working, the first thing to do is turn off the Wi-Fi. Believe it or not, this might tell you that the ethernet is working. ... Right-click on the icon, go to Open Network and Internet Settings, then the Wi-Fi tab, and toggle off.

HP Computers &... | Answered on May 28, 2020


This Error 1702 problem can occur if all the following conditions are true:
  • You originally installed Office from a network administrative installation.
  • The network administrative installation is no longer available to you.
  • You are trying to use an Office CD-ROM when you are prompted by the Windows Installer for an Office source location.
  • You click Cancel when you are prompted to insert the CD.
Because the files in an administrative installation are uncompressed, and the files on an Office CD-ROM are compressed, the Windows Installer cannot resolve the differences between the two source types. The resolution to this problem depends on whether you can obtain access to a network administrative installation. Use the following methods, as appropriate to your situation.

If the original administrative installation from which you installed Office is not available, you can use a different administrative installation for the Office source file location. To do this, follow these steps:
  1. Click Start and then click Run.
  2. In the Open box, type a command line similar to the following, and then click
    OK new network path\Setup.exe /fvm package name.msi
    where new network path is the full path to the alternative network administrative installation, and
    package name is the name of the Windows Installer .msi package on the root of this administrative installation (for example, Proplus.msi).
  3. Click OK when the update is finished.

HP Computers &... | Answered on May 24, 2020


https://www.youtube.com/watch?v=1_ssncypf_I

HP Computers &... | Answered on May 24, 2020

Not finding what you are looking for?
HP Broadcom NetXtreme Network Adapter Logo

Popular Tags

9 questions posted

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

HP Computers & Internet

  • HP Computers & Internet

Most Popular Question

lost local

  • Computers & Internet
Loading...