20 Most Recent KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher Questions & Answers

its just clipped over the cap remove and clean also check the seal is not damages on the pipe that goes into case.

KitchenAid 24... • Answered on Jun 18, 2017

It can be the issue with defective float switch. The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. One more thing, if your dishwasher gets stuck in a cycle first try shutting off the breaker for at least 5 minutes if this does not correct the problem you will need to replace the timer / electronic control.

KitchenAid 24... • Answered on Jul 23, 2016

Sounds like a thermal fuse that is a less than $20 part. remove the top 6 screws in the door that hold the plastic front panel on. Behind that is a circuit board and a white flat 1" square fuse with two wires going to it. make sure power is off at breaker. Test with an meter to see if any current is going thru. If not, that is most likely your problem, and just follow the fuse replacement kit instructions carefully, including putting the new wires on the new fuse like they say. Otherwise, the original wires going to the fuse will blow it too.

Should take about 20 minutes.

KitchenAid 24... • Answered on Mar 11, 2015

Try using "Finish" dishwasher tablets with the power ball. And make sure your rinse agent tank is full.

KitchenAid 24... • Answered on Dec 12, 2014

Use DeBruce Polish this Non-Toxic Odorless multi-surface cleaner works perfect. Find them at debrucepolish.com. Try on your cook tops , you will be glad you did. DeBruce Polish Non Toxic All Metal Multi Surface Cleaner debrucepolish...

KitchenAid 24... • Answered on Jan 08, 2014

There is a fuse link that needs to be replaced in the control panel. It is easy to do. The new fuse comes with wires attached. Use them. Resistance in the old wires will just blow the new fuse again. Use a screwdriver to remove the panel cover. Unplug or turn off breaker before doing so. I generally order two of the fuses at a time so I have an extra one on hand.

KitchenAid 24... • Answered on Dec 30, 2013

I'm thinking dishwashers is installed in correctly. Too low causing an issue. Have a tech look at it.

KitchenAid 24... • Answered on Nov 17, 2013

check the float switch on the righthand side on the bottom in the corner it should click and move freely

KitchenAid 24... • Answered on Nov 16, 2013

Maytag Quiet Series 300. The lights flash in sequence starting from the outside traveling inward. The timer counts backwards from 50 to 1. Then the sequence starts over. and continues over and over. I'm able to clear it when the time reaches 1 or 2. It stays off for a while (3-4 hours) then starts over. I can not clear the countdown until it reaches 1 or 2. After I clear it the dishwasher will work, but until then, no way. This happens with the door open or closed.

KitchenAid 24... • Answered on Nov 16, 2013

Sounds like your heating element and/or temperature sensor. Most machines will stop at a point in the cycle to heat the water and will only move on when a certain temp is reached. These parts are fairly cheap.

KitchenAid 24... • Answered on Oct 10, 2013

Not finding what you are looking for?
KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher Logo

284 questions posted

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers


Level 3 Expert

4376 Answers

Cindy Wells

Level 3 Expert

6259 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

KitchenAid Dishwashers

  • KitchenAid Dishwashers

Most Popular Question

maytag quiet series 300

  • Dishwashers