20 Most Recent Kenmore 3.2 cu. ft. Plus Top Load Washer Questions & Answers

0helpful
1answer

How to remove aggitator from center of machine to

Pry the top lid off the agitator.
Remove the plastic shield inside.
Use a 7/16 socket and extension to remove the bolt.
Pull the agitator off the shaft.
5/29/2019 8:18:49 PM • Kenmore 3.2 cu.... • Answered on May 29, 2019
0helpful
1answer

Washing machine shakes badly during spin cycle. I

If you have moved it recently there were some Kenmore washers that had pins on the tub underneath that fit into sort of cups. I leaned mine over and didn't get them back into place and it shook like a earthquake . There are some machines with bumpers underneath that keep the tub from moving too far to the sides. See if you can move the tub by hand side to side on all four directions to check movement. Go online and check your model for recalls, consumer complaints, world of wealth on the net.
11/27/2017 5:48:14 AM • Kenmore 3.2 cu.... • Answered on Nov 27, 2017
0helpful
1answer

Bought a Model A412 from

Maybe lid switch is bad. I think that model has a fuse in the switch assembly if I remember correctly.
9/28/2017 2:27:57 AM • Kenmore 3.2 cu.... • Answered on Sep 28, 2017
0helpful
1answer

How to remove the cap on Kenmore Elite Calypso washer

you'll need to access the pump and remove the hoses. Clean the inlet screen.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
2/2/2016 9:49:06 PM • Kenmore 3.2 cu.... • Answered on Feb 02, 2016
0helpful
1answer

Won't stop filling up. Water

Hello,

Their are 2 possibilites causing it to overflow

1) the water inlet valve that the hoses from the house plumbing attach to is sticking open,when it sticks it will stick open regardless if thier is power to the machine or not,so to determine if that is the problem,start the washer and quickly unplug it,if the water continues to fill, that valve is sticking

2) the water level switch is defective,do the same as far as starting it,if the fill stops when power disconected it's the water level switch that is in need of replacement

Good luck, i hope this helps.

Gene
12/3/2015 7:12:05 PM • Kenmore 3.2 cu.... • Answered on Dec 03, 2015
0helpful
1answer

Washer kenmore leaking water out bottom

Its very possible it could be one of the tubes that run to the fabric softener or detergent.
11/8/2015 4:51:19 PM • Kenmore 3.2 cu.... • Answered on Nov 08, 2015
0helpful
2answers

Will not agitate after water fill up. Motor makes whining sound.

Hi,

It sounds like it could be the coupling that has worn or broke, to verify this put the washer in spin, let it drain the water out (if it will) then turn off the timer or open the lid, wait 10 seconds or so then start back up in spin. If the washer just whines then it is most likely the coupling. I have put together some instructions on this if you follow this link it will tell you more about it and how to replace it if you wish. Let me know if this helps.

http://www.fixya.com/support/r4670549-drive_coupling_replacment
9/28/2015 5:27:14 PM • Kenmore 3.2 cu.... • Answered on Sep 28, 2015
0helpful
2answers

I have a Kenmore Heavy Duty 90 Series, Extra

replace the motor coupling.
7/17/2015 12:18:17 AM • Kenmore 3.2 cu.... • Answered on Jul 17, 2015
0helpful
1answer

I need the year model of whirlpool washer model

I bought mine brand new December 2005. Kenmore washer.
3/4/2015 8:42:04 PM • Kenmore 3.2 cu.... • Answered on Mar 04, 2015
0helpful
1answer

What is the capacity of

What series is this washer? I’m happy to help further over the phone at https://www.6ya.com/expert/tami_f8d2d553d5094045
3/3/2015 9:48:04 PM • Kenmore 3.2 cu.... • Answered on Mar 03, 2015
0helpful
1answer

I have a kenmore 80

Good for you. I don't think this model has a belt, I believe it is a direct drive with a coupler. Most likely, if you can hear the motor, the coupler has done it's job and sheared. The coupler is 20 bucks and my wife and I just changed ours out. I need the entire model number and I will get you the part schematic and we will get you going.
2/26/2015 9:49:25 PM • Kenmore 3.2 cu.... • Answered on Feb 26, 2015
0helpful
1answer

Kenmore Series 80 washer NO High Speed Spin

It could be a timer, motor or wiring problem. You would need to check for 110 volts at the timer or motor when in the higher spin mode. If you are getting 110v you have a bad motor. No or low volts you have a bad timer. The motor is either a 2 or 3 speed motor and you would have to determine which winding to check for the 110v. The schematic is usually glued to the inside rear cabinet. Please rate this post.
11/9/2014 7:14:15 PM • Kenmore 3.2 cu.... • Answered on Nov 09, 2014
0helpful
2answers

What is the capacity of Kenmore model

This may or may not help.

http://www.managemyhome.com//mmh/lis_pdf/OWNM/L0305295.pdf


10/29/2014 12:32:42 AM • Kenmore 3.2 cu.... • Answered on Oct 29, 2014
0answers
0answers
Not finding what you are looking for?
Kenmore 3.2 cu. ft. Plus Top Load Washer Logo

582 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

Cindy Wells

Level 3 Expert

6477 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Washing Machines

  • Kenmore Washing Machines

Most Popular Question

want know stack kenmore elit gas dryer

  • Washing Machines
Loading...