20 Most Recent GE WPGT9360EPL Top Load Washer - Page 7 Questions & Answers

This suggests a communication issue. https://www.fixya.com/support/t29731810-ge_fridge_displays_0000 Call a local GE refrigeration engineer. There is a video if you want to try some things. https://www.google.com/search?q=Ge+model+pfss5rkzhss+is+flashing+0+on+the+control+panel ..

Ceck for a leak on the outlet pipe fitting.

Your question is confusing. A washer doesn’t spin when it washes. It agitates. A washer fill with water, agitate, drain then spin water out. Please reword your question.

sounds like water solenoid going bad

Try a Power Rest of the control board.

Washer - Resetting the Electronic Controls

https://products.geappliances.com > appliance > gea-sup... To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a ...

• Top Load Washer - Hydrowave Motor Reset

  https://products.geappliances.com > appliance > gea-sup... Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 ...

Question edited for clarity, capitalization and typo. Question moved from MISC to make category. Sound like a control board issue or connection issue. Call for service for correct diagnosis. If it is old, consider replacement.

if drive belt ok check under agitator and replace worn cogs

Suck some air out of hose. Needs negative pressure when empty. You can try to fill basin up to max fill level. Disconnect hose to let pressure bleed off. Drain, and you should be set

It is usually caused by worn Clutch Dogs or a fault with the Gearbox. It is a messy job and requires special tools. Call for service. Or depending on age, buy a new energy efficient front loader. Less water, electricity and detergent.

Hello Sounds like your likely problem would be the Display Board or User Interface Board part # WH12x10544 , Hope this helps .

Although you posted that a few years ago, I'll still give my 25¢ From top left to right: red pin, blank blank Middle left to right: black, white, blue Bottom left to right: orange, yellow, purple Top left pin (red) is positive and 1st left pin in middle (black) is negative. Straight 120v, but I don't know how to vary the speed by utilizing the other pins

I would check the drum bearing and mounting.

Yes, you can try a power cycle on it, but you probably need a service call. Likely a control board issue.

https://f01.justanswer.com/smitty1486/f1e3636b-6c6d-4de9-b0e7-bcf462c895de_ScreenHunter_5249_Dec._09_08.50.jpg https://www.justanswer.com/appliance/auy5a-ge-profile-range-it-s-showing-f50-code-whats.html

You need to replace the machine. Most parts are no longer available and the part that is likely to be faulty is not even listed on the schematic! The type of machine has a mechanical timer. If you can get into the top unit, you could try spraying some WD40 into any gaps you can see in the lump at the back of the main control knob. There is a small synchronous motor that drives it. https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-90150.pdf Top parts schematic. Click + to enlarge http://assets.geappliances.io/parts/00000000/00018400/00018470.p01_2325.jpg Non availability of parts! https://www.geapplianceparts.com/store/parts/ModelSectionParts/WBSE3120B2WW/1/0/0/0/CONTROLS_&_BACKSPLASH Front Loaders hold just as many clothes, wash better, and use a fraction of the water and electricity using HE Detergent.. ..

It is a job for the Service Techs, they have the special tools needed. videos https://www.google.com/search?q=ge+model+wjre5550h+replace+agitator+dogs ..