20 Most Recent Bosch Axxis WTA4400 Dryers Questions & Answers


It is a heat insulator

Bosch Axxis... | Answered on Jun 13, 2019


Did you check the res to see if it was full? Might be clothes inside the door and it aint shut all the way? never even seen a condenser dryer.
I have the model service manual though HERE

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61


Bosch Axxis... | Answered on Nov 22, 2014


Take the old one out and pay attention to the steps. Reverse the steps to replace the new motor.

Bosch Axxis... | Answered on May 22, 2014


my wte84105gb condenser dryer (bosch) as a symbol on it looks like a glass with wavey lines inside it will not dry please advise what to do .

Bosch Axxis... | Answered on Dec 25, 2012


Hi, If you are having problems with your gas dryer not heatingthe most common problem is that the ignitor goes bad. Even though it glowssometimes it is still not working properly. if you dryer is gas check out this gas no heat tip.... If you have an electric dryer, you can have many differentthings that can go wrong causing the dryer not to heat. check outthis electric no heat tip...

heatman101

Bosch Axxis... | Answered on Aug 18, 2011


Open the top cover holding with three screws. Open the console by opening three screws.Than open timer holding plate(four screws).Timer is attached with two screws with plate.Take the nob out and reverse the procedure.
Thanks.

Bosch Axxis... | Answered on Aug 02, 2011


The problem is with the lower water tank float switch, it is stuck. Take off the right hand side panel (as you are facing the machine) at the bottom you will see a spring mechanism for the belt tension. Beside this there are 2 electrical connectors. Take them off and spray with wd40 or similar. Whilst off give the plastic box they fit 2 a light tap with a hammer to free the float switch. Reconnect and try. If this fails you can over-ride by leaving the left hand of the two plugs off. This will get your machine working but you will not have an indication as to when the water container needs emptying so you will need to remember.

Bosch Axxis... | Answered on Jul 17, 2011


Does the dryer make a humming sound when you try to start it or is it completely silent?

Bosch Axxis... | Answered on Jan 31, 2011


Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.



if you dryer is gas check out this gas no heat tip....



If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.



check out this electric no heat tip...


heatman101
''''''''''''''''

Bosch Axxis... | Answered on Jan 15, 2011


IS THE DRYER A SENSOR DRYER IF SO TRY PLACING A JUG OF HOT WATER INTO THE DRYER, BUT DO NOT EMPTY THE WATER IN THE DRYER, JUST LET THE STEAM OFF THE WATER OPEN THE SENSOR HOOVER DYERS HAVE THIS PROBLEM TO

Bosch Axxis... | Answered on Jan 08, 2011


are you sure it is the element, and yes repairing it is a whole lot cheaper:

http://shop.ebay.com/i.html?_nkw=heating+element+dryer+bosch&_sacat=0&_odkw=heating+element+dryer&_osacat=0&_trksid=p3286.c0.m270.l1313

this should assist you:

http://www.espares.co.uk/advice/tumble-dryers/a/9/1344/how-to-replace-the-heating-element-assembly-o.html

Bosch Axxis... | Answered on Dec 04, 2010


check the inlet filters first and then the out let hose the dryer needs to breath in a lot of air so if any of the inlets or out let pipes are blocked that could put this light on

Bosch Axxis... | Answered on Aug 27, 2010


try replacing the thermistate fuse link

Bosch Axxis... | Answered on Jul 04, 2010


If the belt is not slipping and it has good tension on it still, I would not spend the money right now to replace.

Bosch Axxis... | Answered on Jun 03, 2010


the first thing to check is that you have 220VAC at the plug. If one leg of the circuit drops out you can have this symptom.

Bosch Axxis... | Answered on Apr 20, 2010


take the back panel off and look at the heating element can there is a thermal fuse that has a small reset button on it. push this in if that does not work then you need to check all the thermal fuse as well as the heating element for continuity if there is any of the above mentioned items that do not have continuity then replace the one that does not have anything

Bosch Axxis... | Answered on Mar 13, 2010


It is possible that the heating element has burnt out or a high limit switch (safety device to prevent overheating) has gone out. Element is located at the bottom of the dryer on the oppisite side of the exhaust. Looks like a toaster coil. Any break in the coil and no heat. New elemenrts can be purchased at an appliance parts house with the serial and model numbers for your unit to ensure correct part.
Dave

Bosch Axxis... | Answered on Jan 13, 2010

Not finding what you are looking for?
Bosch Axxis WTA4400 Dryers Logo

38 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Dryers Experts

Cindy Wells

Level 3 Expert

6073 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Bosch Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Dryers

  • Bosch Dryers

Most Popular Question

our bosch classixx condenser tumble

  • Dryers
Loading...