20 Most Recent Westell Wirespeed VersaLink (A99-327W11-00) Router (A99327W1100) - Page 4 Questions & Answers

Good day.
You can find it at the bottom of the router. There is a sticker there that says Product Key or KEY. You should be able to find it with ease.

What it is talking about is a button on your wireless router that will probably have a picture of a small lock on it.

Besides pressing that button you will also need the pass key which should be on a sticker on the router somewhere. It will usually be a 4 to 6 digital number, no letters.

Hope that helps

Just "reset" the router back to its "factory" settings, and then configure it, setting the password to something that you can remember.

A disconnecting wireless can be caused by any number of things. please click on this link and follow my instruction for a possible solution.
http://www.fixya.com/support/r3559120-wireless_router_disconnecting

use a pencil or pen to push the little reset button on the back of the modem, resets the user and pass

press CTRL key plus the R key
type cmd and press ok
in the command prompt type ipconfig, enter
copy default gateway address (probably 192.168.1.1) and paste it on the internet browser, enter
enter:
ID: admin
pass: password
the router's interface page should have loaded, otherwise the login or password was changed, you may need to reset the router.
If you had access then go to the wireless security option and enable WPA(2) security
Reconnect the computer with the new passphrase. If not clarify at what point you are stuck.

http://www.dslreports.com/faq/westell?text=1

Westell routers have an IP of 192.168.1.1
Type that in the address bar of your browser to be able to access your router. The login for most westell is:
Username: admin
Password: password Then this will give you access to setup your router with security which will allow you to set a password.

In order to activate the wireless 3G modem you have to connect it to your computer and run the verizon software that is included with the device.
If the software isn't on a disc, it should auto start when you plug in the device.
If you're still having issues with the product, call Verizon at (888) 294-6804.
They should be able to provide any assistance you require outside of what I suggested.

First, please check the Windows Hardware and Software compatibility list to assure your device is appropriate for the OS you are using. If you are not using Windows 7, you will find links at the site to other supported OS. Here is the link: http://www.microsoft.com/windows/compatibility/windows-7/en-us/default.aspx

Here is the link to the company: http://www.westell.com/

Good luck with your device.

Yes it will, however it will only run at Wireless-G speeds as it is only a Wireless G router. You will not speed any speed difference while on the internet but you may see it when you are transferring files from one computer in the house to another over your network.

Hi,

Welcome to FixYa! A WEP key is a security code used on some Wi-Fi networks. WEP keys allow a group of devices on a local network (such as a home network) to exchange encoded messages with each other while hiding the contents of the messages from easy viewing by outsiders. For you to be able to change the WEP key, please follow the instructions below.

1. Open up a browser.

2. Type 192.168.1.1

3. Type admin as the username and admin as the password ( if admin is not accepted as the password,try to use password as the password )

4. Click on Wireless Connection Tab.

5. Click on Basic Wireless Security Settings.

6. Scroll don on the page and you will see there the WEP key option.

7. Type your preferred WEP key which consist of 10 characters, 0-9 and A-F only.

8. Click Save Settings.

Hope this information will help. Thank you for using FixYa!

Hi,

Welcome to FixYa! I believe that when you're trying to connect wirelessly it's not asking for the network key or other users are able to connect to your network. Please follow the steps below for you to be able to make your connection secure.

1 Open your web browser, type " http://192.168.1.1/ " into the address bar and hit "Enter."

2 Use "admin" as the username in the pop-up box and leave the password blank or try to use " admin" as the password as well.

3 Connect to the Internet and click on "Internet Setup."

4 Select your connection type from the drop-down menu. Choose "DHCP" for cable modems or "PPPoE" for most DSL modems. If you are unsure of these options, check with your ISP.

5 Set a service set identifier (SSID) to identify the router and change the password.

6 Encrypt your wireless connection using a Wireless Encryption Protocol (WEP) key. Under the "Wireless Security" option, enter a passphrase and click "Generate." This will generate a password which will need to be used by any client connecting to your router

Hope this will help...Thank you for using Fixya...

Hi,

Welcome to FixYa! There are two ways of getting the WEP key for your router. Easiest way is to check underneath the router and you will see there the default WEP key. Or, follow these steps for you to be able to get the WEP key set by your ISP.

1. Connect the computer directly to the router.

2. Open up a browser and type 192.168.1.1

3. It will ask for a username and password,type admin as the username and admin as the password, if it did not push through,try password as the password.

4. Once you have the GUI ( Graphical User Interface ) click on Wireless Settings.

5. Click on Basic Security Settings.

6. You will be able to see there the wireless key which is the same as the WEP key. You can go ahead and personalized that security key as well.

Hope this will help...Thank you for using FixYa...

Hi,

You can give a try using the HP Network diagnostic tool and it should give you your network details

Click on the link below and follow the steps

HP Network Diagnostic Tool


Regards,
Ron

reset button in back of router its small button push in on it.then go to tools diagnose.

Sorry for your loss.

• Note: Resetting your router to the factory defaults not only changes your gateway user name and password to the factory default values, but it also deletes all your home network settings. This includes the SSID and network encryption key. After you reset your gateway to the factory defaults, your home network won't be accessible until you reconfigure your router and all your network devices to use the same SSID and network encryption key.

To reset your VersaLink 327W gateway to the factory settings:
Hold the reset button on the back panel of the VersaLink gateway for 30 seconds.

• All your settings will be lost including network encryption information, MAC Address filtering information, and any SSID information you have entered.
• The gateway user name and password will revert to the default of Admin as the user name and Password as the password.
• You will need your user name or password to reconfigure the unit..

Your VersaLink 327W gateway is now using the default settings for the network configuration. This includes the default SSID and network encryption key. You must re-configure your VersaLink gateway to match your previous settings that were assigned to all other devices on your wireless network. Otherwise, no other network devices will be recognized.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

http://download.cnet.com/WirelessKeyView/3000-2092_4-10614187.html Download and run, and enjoy your internet! Just make sure you're in range of the router in question. Leave feedback!

To open the set up page of the router of the router , one of your computer should be able to go online through the router.
It could be a wired computer or wireless computer.
If it is a wireless computer then make sure that the computer is connected to your own wireless network.
Do not change any wireless settings on the router using a wireless computer.
OK ! Now you have a computer online through the router and you want to open the set up page of the router.

First step is check the IP address of the computer.
Check the IP address and the Default gateway on the computer.

For Windows XP

START ==> RUN ==> type in cmd in the RUN box==> click OK or Hit ENTER . You will see a black window that is a command prompt . In the black window type in " ipconfig " ==> and Hit ENTER on your key board .

For Windows Vista and Windows 7

click on START ==> type in cmd in the start search box ==> enter ==> you will see the black window. Type in " ipconfig "you will see a lot of information. Try to find out the local area connection IPv4 address .

Note down the Default gateway number.

For MAC OS

Click APPLE icon in the right top corner of the computer. Go to System Preferences ==> go to Network ==> you will find the option Built in Ethernet or Airport whichever is connected. If you go to that you will find the Ip address and router Address.

The default gateway is the IP address of your router.

This IP address of the router will be used to open the set up page of the router

Now you got the IP address of the router.Open the Internet Browser ( Internet Explorer, Firefox, Safari )

In the Address bar of the browser Type the IP address of the router.

Do not type http:// or www just type in the IP address only.

It will ask you for the user name and the password of the router.

This is the User name and the password of the router and NOT the wireless password. On a wireless router, there are 2 passwords. One is to access the router and the other one is for the wireless network.

For most of the routers the default password will be " admin " . for some routers the default password is " password ". For Linksys router the default password is admin and no user name.

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

Call Clearwire