20 Most Recent
Epson TM-T88III Thermal Printer - Page 5 Questions & Answers
Not printing, paper came out blank
1. disconnect printer from computer, turn off
2. re-seat thermal paper, make sure it's loaded correctly
3. press and hold paper feed button while turning the printer on
4. if print test is successful, reconnect to computer
5. print test page from printer driver
Relatively new printer stopped printing.
hello,
There are few things that could cause this problem, firstly, you will need find out if the printer as not as not run out of toner/ink, because, since it feeds paper but no printing, the toner/ink on the printer might have finished and need to be replaced. in this case, you will need to check the toner/ink on the printer or replace the ink. toner on the printer before it can print again.
Another option is, uninstall the printer driver from the system and re-install back after uninstalling, ensure you restart your system after re-installing, this will fix the problem of no printing with your printer.
Take care.
Does epson tm-t88iiip have a ribbon
No. thermal printers do not use ribbons or ink cartridges. They have thermal heads that heat up and use that heat to print on the specially treated, heat sensitive paper rolls. If the printer has stopped printing, check to see if the paper is thermal and loaded correctly (shiny side facing the front when it feeds).
Epson tm-t88iv not showing logo
Try adding a separator page with
\
\H1C\H70\H01\H00
\
as the code. Copy and paste the above into notepad save the file in the system32 directory, open your printer's properties from the printers file folder in control panel. go to advanced tab of properties, click on separator page. add the notepad file you created. A separator page is printed at the beginning of every print job. The code came from epson expert.com
Is the Epsom TM88III printer
Yes its compatible as long as you use the latest driver for windows. I strongly suggest that you update your firmware for it to run on windows.
How do you change the
IF it is a THERMAL printer, they usually use special Thermal paper . It burns the image onto the paper with a thermal print head.
There is NO ink to change
I can't get my cash drawer to work is there a
You must be sure the voltage to the cash drawer and the printer are correct. A 24 volt RJ12 printre connection to the solenoid of a 12 volt cash drawer will cause damage. If the drawer was working and stopped, it is possible the solenoid may be the problem.
Ink pad full
Try to follow this steps:
1. Long press the power button for 10 seconds.
2. While pressing the power button disconnect the power cord at the back of your printer.
3. Turned it On again then try to print.
If it can print, Every time you print just always perform that solution because your printer are meet the maximum number of copies to be print that's why the problem are back. You can also downlaod the reseter program of that printer to permanently solve that problem.
Looking for a Windows 7 driver for the Epson
1st You download Printer Driver.
Epson TM Printer
After this install the Printer driver in the system.
Installation of Printer Driver
- Go to the control panel
- Click on the System Icon
- Click on the Hardware Tab
- Click on the Device Manager then
- Select the Unknown Device or printer device where yellow Question Marks sign on it.
- Right click on it and uninstall it.
- After this go to the top of the device manager and click on scan for hardware changes.
- Driver installation Wizard start.
- Brows Your Driver from the Hard Disk and click on next.
- Driver will be install.
I am sending raw data to the printer. Where to
Hi,
This feature allows experienced users to see exactly what data is
coming to the printer. This can be useful in finding software
problems. When you turn on the hex dump function, the printer
prints all commands and other data in hexadecimal format, along
with a guide section to help you find specific commands.
To use the hex dump feature, follow these steps:
1. After you make sure the printer is off, open the cover.
2. Hold down the FEED button while you turn on the printer.
3. Close the cover.
4. Run any software program that sends data to the printer. The
printer prints “Hexadecimal Dump” and then all the codes it
receives in a two-column format. The first column contains the
hexadecimal codes and the second column gives the ASCII
characters that correspond to the codes.
Hexadecimal Dump
1B 21 00 1B 26 02 40 40 . ! . . & . @ @
1B 25 01 1B 63 34 00 1B . % . . c4 . .
41 42 43 44 45 46 47 48 ABCDEFGH
❏ A period (.) is printed for each code that has no ASCII
equivalent.
❏ During the hex dump all commands except DLE EOT and
DLE ENQ are disabled.
5. Open the cover to set the printer off line, so that it will print the
last line.
6. Close the cover and turn off the printer or reset it to turn off the
hex dump mode.
PLEASE CHECK THE LINK TO GET THE ESC CODES:
http://www.mit.edu/~vona/MSim/vona/terminal/VT100_Escape_Codes.html
Hope this helps u ..............
Invalid operation 425: the printer
Hello, Joyce.
If this is used by multiple users, be certain that others are logged out (and PCs shut off if necessary).
Also, from Epson Support: be certain to set to share the OPOS in SO Mgr config. This is under SO Mgr> File>
Config> Options> POS Options> 'Share the OPOS printer with other applications'.
Hope this helps.
Not finding what you are looking for?