Top 20
HP LaserJet 4730 MFP Printer Questions & Answers
1 Answer
How do i cold reset
Cold reset
A cold reset unlocks menus that have been previously locked and resets all control panel menu items to the factory defaults. A cold reset does not clear the values in the service menu, such as the serial number and the page counts.
NOTE: Before performing a cold reset, print a menu map and a configuration page. Use the information on these pages to reset customer-specific settings.
CAUTION: All HP Jetdirect settings are also reset. Be sure to print a configuration page before performing a cold reset. Make note of the IP address that is listed on the Jetdirect configuration page. You will need to restore the IP address after performing a cold reset.
To perform a cold reset
1. Turn the MFP off and then on.
2. When the memory count appears on the control panel display, press and hold 6 until all three LEDs flash once and then stay on. This might take up to 20 seconds. wait until the machine display gives you the next option this may take upto 2 mins again
3. Press 3 four times until COLD RESET appears on the control panel display.
4. Press 6 one time. The MFP continues its initialization sequence.
a cold reset has been performed.
HP LaserJet 4730...
|
3,108 views | 1 helpful votes
1 Answer
Error 30.01.02 before and after change of scannertop
30.1.2= A jam has occurred in the ADF. Recommend action, turn the MFP off and then back on to try to clear the message.
If the message indicates that a jam has occurred, clear the jam, if the message is still there. Check that the cable between the print engine and the scanner is secure..
Turn the MFP off, remove all memory DIMMS or third party DIMM from the MFP (Do not remove the firmware DIMM) remove all EIO device from the MFP. Turn the MFP on
if the erropr no longer exists, reinstall each DIMM and EIO device one at a time, make sure to turn the MFP off and no again as you install each device. replaced a DIMM
or EIO device if it cause the error, if problem persists upgrade the firmware before replaced the DC controller. Replaced the formatter and calibrate the MFP.
take a look here
http://h30499.www3.hp.com/hpeb/attachments/hpeb/bsc-420/34967/1/357783.pdf
HP LaserJet 4730...
|
163 views | 0 helpful votes
1 Answer
Error 59.51 on hp laserjet 4700
A 59.51 error would normally indicate a problem with the cyan drum drive motor DC controller. First of all I would recommend resetting the printer and unplugging it from the wall for a minute or so while it is off. Sadly if this doesn't clear the error any further fixes would involve cold resets, disconnecting and replacing components.
In which case it would probably be best to call an engineer unless your feeling particularly brave.
HP LaserJet 4730...
|
634 views | 0 helpful votes
2 Answers
Hp 4730 fuser reset
Anyone with information on how to reset the Fuser page count without chanigng the fuser on HP 4730 MFP? The fuser in the unit is in very good condition and replacements are not cheap. Any help would be much appreciated.
HP LaserJet 4730...
|
748 views | 0 helpful votes
1 Answer
How do i scan images using the hp 4730 mfp
check under general reference (link below). it should mention how to fax, e:mail and copy. if you copy to file / pc that should work as the scanner.
otherwise make sure the "scanner" facility is installed as some MFP's do not come with all facilities installed. (and therefore may not give the option on the screen.)
http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?lang=en&cc=us&prodClassId=-1&contentType=SupportManual&prodTypeId=18972&prodSeriesId=468688
HP LaserJet 4730...
|
708 views | 0 helpful votes
1 Answer
Incoming faxes on the laserjet 4730 mfp look like
Hello,
Unexpected image like barcode as shown below can occur when using the automatic document feeder (ADF). You are using the ADF for incoming faxes. So the problem occurs.
If the copy does not look at all like the original document, make sure that no media is on the flatbed glass from a previous copy job.
I hope this helps.
If you would like to vote for the answer, this will help the others to see the similar problems solved and also will be a satisfaction factor for me to continue helping you.
All the best.
HP LaserJet 4730...
|
187 views | 0 helpful votes
1 Answer
Yellow shadowing on paper hp4730 mfp how do I
Try a manual calibration.
1. Press the MENU button.
2. Press the down arrow until “CONFIGURE DEVICE” appears on
the display.
3. Press SELECT.
4. Press the down arrow until “PRINT QUALITY” appears on the
display.
5. Press SELECT.
6. Press the down arrow until “QUICK CALIBRATE NOW” appears
on the display.
7. Press the “SELECT” to start the calibration.
HP LaserJet 4730...
|
263 views | 1 helpful votes
Not finding what you are looking for?
