20 Most Recent Toshiba E-Studio 356 Multifunction Copier - Page 3 Questions & Answers


C447 Error - Heater lamp abnormality after abnormality judgment (temperature abnormality at ready status)

Power voltage Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) Thermopiles • Check if the fuser belt center and side thermopiles (front, rear) are installed properly. • Check if the harnesses of the fuser belt center and side thermopiles (front, rear) are open circuited. Power supply unit and fuser unit • Is the fuser unit installed correctly? • Check if the heater lamp is broken. • Check if the connector of the heater lamp is disconnected. • Check if the thermostat is blown • Check if the connectors of the power supply unit are disconnected (power supply unit AC output connector CN408, CN409 and LGC I/F connector CN404 CN405). • Check if the power supply unit is abnormal. LGC board • Check if the connectors CN333, CN345 and CN361 are disconnected. • Check if the conductor pattern on the LGC board is short circuited or open circuited. Status counter After repairing the matter which caused the error [C411/C412], perform the following: • Turn ON the power while [0] and [8] are pressed simultaneously • Key in "2002", then press [START]. • Change the current status counter value "1 " or "2 " to "0", then press [OK] or [INTERRUPT] (to cancel [C411/C412]). • Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state.
5 Clear the status counter Change the current status counter value (08-2002) "3", "5", "6", "9", "19", "21", "22", "23", "24", "25", "27", "29" or "32" to "0" for [C44X], taking the same procedure as that for [C41X]. * The status counter value is as follows in the following cases. - The error occurred during warming-up: "3", "5" or "6" The error occurred after the equipment has become ready: "7". - The temperature detected by the fuser belt center thermopile is 220°C or higher, the temperature detected by the side thermopile is 230°C or higher or the temperature detected by the front thermopile is 250°C or higher: "9", "19", "21", "22", "23", "25", "27" or "29" - The error occurred during printing: "24" or "25". - The error occurred during energy saving: "27". - A paper jam occurred: "29".

Toshiba Office... | Answered on May 13, 2020


Toshiba e-Studio 356. Description: Power-ON jam: The paper is remaining on the paper transport path when power is turned ON. Remedy: 1 Open the cover of the unit/ area whose picture is blinking on the control panel. ... Yes Remove the paper.
https://printcopy.info/index.php?mod=erc&brand=Toshiba&model=e-Studio%20356&code=E030
https://www.manualslib.com/manual/1023591/Toshiba-E-Studio2330c.html?page=972

Toshiba Office... | Answered on May 05, 2020


24/7 Customer Services
  1. Efficacious Solutions to Troubleshoot Toshiba Fax Error 0050: ...
  2. Solution 1: Allowing Fax Machine to Redial the Busy Number. ...
  3. Solution 2: Placing of a direct call at the Voice Line. ...
  4. Solution 3: Try sending the document as a PDF attachment to an email message.
https://www.toshibasupport365.com/blog/resolve-toshiba-fax-error-0050/

Toshiba Office... | Answered on Mar 28, 2020


https://www.toshibasupport365.com/blog/fix-toshiba-1370-error-code/

https://www.slideshare.net/toshiba8514/how-to-fix-toshiba-1370-copier-call-for-service-error-call-1-844-3930509

Toshiba Office... | Answered on Mar 23, 2020


Do you have firmware?
you have to update firmware using pc update tool.

Toshiba Office... | Answered on Mar 19, 2020


You wants new feelings ? ?? add me. ?? You won't bedis??appointed! ?? write me ??==>> v.ht/itnZ

Toshiba Office... | Answered on Mar 13, 2020


Here is the link for the Toshiba support site. You will need more specific model numbers and/or serial numbers than you gave in your question. I hope this helps you. Drivers Software Support Toshiba

Toshiba Office... | Answered on Mar 06, 2020


After update firmware got C270 error?

C270 can be caused by CIS unit, CIS harness, main board...

Toshiba Office... | Answered on Mar 05, 2020


search first here.
https://duckduckgo.com/?q=Toshiba+Error+Code+0Xc000021A&atb=v186-1&ia=web

that was stop code in the windows BSOD right?
I means windows is corrupted
or HDD is bad, causing windows to be corrupted

running windows 10, just boot the PC 3 times and let the PC do the magic repair, but you never told the OS you run so...
w7/8/10?

Toshiba Office... | Answered on Feb 25, 2020


https://printcopy.info/?l=ru&mod=erc&brand=Toshiba&model=e-Studio%202505H&code=C449
Service manual online at link above
Quoting from link above: "
  • Code: C449
  • Description:Fixer temperature of 240°C or higher during printing
  • Causes:MAIN board
  • Remedy:1. Check the thermistors 1. Check if the connectors are disconnected. 2. Check if the center and edge thermistors are in contact with the surface of the fuser roller properly? 3. Check if the center and edge thermistors are not deformed or dirty. 4. Check if the harnesses of the center and edge thermistors are open circuited. 2. Check the heater 1. Check if the heater is broken. 2. Check if the connector of the heater is disconnected. 3. Check if the harnesses are connected properly to the terminals of the heater lamp. 4. Check if the thermostat is blown. 3. Check the MAIN board 1. Check if the connectors CN10 are disconnected. 2. Check if the conductor pattern on the MAIN board is short circuited or open circuited. 3. Replace the MAIN board 4. Check the power supply 1. Check if the connectors are disconnected. 2. Replace the switching regulator. 5. Clear the status counter After repairing the matter which caused the error [C449], perform the following: 1. Turn ON the power while [0] and [8] are pressed simultaneously. 2. Key in "2002", then press [START]. 3. Change the current status counter value "9", "19", "21", "22", "23", "25", "27", "29" or "45" to "0", then press [OK] (to cancel [C449]). 4. Turn the power OFF and then back ON. Make sure that the equipment enters the normal ready state. "

Toshiba Office... | Answered on Feb 19, 2020


They usually have green or blue tabs that you pull towards you

Toshiba Office... | Answered on Jan 15, 2020


[F120] Database abnormality

(1) Rebuild the databases. (Perform 08-684.)
(2) If the error is not recovered, initialize the HDD. (Key in "2" at 08-690.)

Toshiba Office... | Answered on Jan 13, 2020


https://printcopy.info/?l=ru&mod=erc&brand=Toshiba&model=e-Studio%20195&code=C97


https://www.fixya.com/support/t13306989-toshiba_e_studio_207_c97_error_solution

Toshiba Office... | Answered on Dec 06, 2019


C440 is fuser error, enter 08-2002, clear the value to "0" and restart machine. If still persist, u need to check the fuser unit especially the thermistor...

Toshiba Office... | Answered on Nov 27, 2019

Not finding what you are looking for?
Toshiba E-Studio 356 Multifunction Copier Logo

Popular Tags

33 questions posted

Ask a Question

Usually answered in minutes!

Top Toshiba Office Equipment & Supplies Experts

Timothy Van Der...

Level 2 Expert

152 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers

Are you a Toshiba Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Toshiba Office Equipment & Supplies

  • Toshiba Office Equipment & Supplies

Most Popular Question

toner cartage not recongnized in toshiba

  • Office Equipment & Supplies
Loading...