Intertherm P3RA-048K Air Conditioner - Page 2 - Answered Questions & Fixed issues
Best way to clean indoor airconditioning coils
Open up unit locate evap.coil with small brush clean coil then use evap.coil cleaner its self rinsing but if you can wash with hose without getting water inside home do so.
7/27/2013 8:30:40 PM •
Intertherm...
•
Answered
on Jul 27, 2013
•
100 views
Recharge unit
Blue hose goes to suction side which would be larger size copper line this is your low side.red hose to other side smaller line,high side.Yellow hose to freon container.
7/27/2013 8:21:23 PM •
Intertherm...
•
Answered
on Jul 27, 2013
•
71 views
Fan spinning backwards
If its the original mtr. or was working fine before then mtr is bad replace mtr with new capacitor
7/27/2013 8:12:36 PM •
Intertherm...
•
Answered
on Jul 27, 2013
•
202 views
Condensor fan spinning in reverse
THE MOTOR IS A 3 PHASE MOTOR JUST SWITCH ANY TWO WIRES TO THE MOTOR AND THE MOTOR WILL RUN THE OTHER DIRECTION. BE SURE TO DISCONECT THE POWER TO THE UNIT BEFORE DOING THIS.
6/30/2013 7:10:06 PM •
Intertherm...
•
Answered
on Jun 30, 2013
•
188 views
Furnace will not run complete cycle ,several clicks and the and the furnace shutdown and restarts, will not bring the house to temperature
If it's a 90%+ gas furnace, check the combustion air pvc pipe for blockage, if not enough air for proper combustion, control board will shut down the flame to keep from burning poorly! Check your air filter, there's an overtemperature safety switch in the heat exchanger to protect the furnace/ your house, and low airflow will cause the heat exchanger to overheat. Finally, check to see if the flames actually ignite, if no flame, the controller will reset and try again, then if no flame, the controller will reset and try again, then if no flame, the controller will reset and try again, then if no flame, the controller will reset and try again.... get the idea? :) If this is the case, check my other solutions, I just answered someone elses question about non ignition. Hope this helps.
4/12/2013 5:19:47 AM •
Intertherm...
•
Answered
on Apr 12, 2013
•
182 views
Q3RD 048K
Check the capacitor and verify if the motor is receiving voltage, if not ithen the motor is bad.
1/18/2012 8:51:57 PM •
Intertherm...
•
Answered
on Jan 18, 2012
•
203 views
Just replaced pressure switch on intertherm m1mb
CHECK FLUE FOR OBSTUCTIONS AS WELL AS COMBUSTION AIR INTAKE FIRST. THEN CHECK TO SEE IF THE FURNACE DRAIN IS OPEN AND NOT CLOGGED [ONLY IF YOUR FURNACE IS A CONDENSATING HIGH EFFICIENCY MODEL, typically the flue pipe will be 2 or 3 inch pvc pipe] over the years more often than not, it is an obstruction or poor drainage which will not prove the pressure switch to allow the burner to ignite. in rare cases the furnace control board could be bad as well.TRY DISCONNECTING FLUE AND COMB. AIR AT FURNACE JUST TO SEE IF FURNACE WILL IGNITE. HOPE THIS HELPS!!!!!!
12/12/2011 4:07:58 AM •
Intertherm...
•
Answered
on Dec 12, 2011
•
698 views
My oil furnace has a strong smell of oil when it
PLEASE call a serviceperson,but, it sounds to me like your furnace is burning dirty and needs the electrodes cleaned or replaced as well as the proper oil nozzle and filter hope this helps you out, OH, one more possibillity is the furnace or flue chimney could be stopped up or the air mixture is not set properly on the burner. ANY OR ALL OF THESE COULD CAUSE CARBON MONOXIDE POISONING C/M IS ODERLESS AND COLOROUS AND CAN KILL YOU QUICKLY. CALL A REPUTABLE SERVICE PERSON PLEASE!!!!!!!!
12/12/2011 3:47:09 AM •
Intertherm...
•
Answered
on Dec 12, 2011
•
316 views
I have an intertherm electric furnace. the heat
It is possible that high temp limit is shutting you down.make sure your blower is running when t-stat is calling for heat.if notstart at the heat sequencer which cuts the blower on with first bank of heat. it will be dangerous and difficult to troubleshoot this prob without a multimeter and experiance with elect. components
12/12/2011 3:29:56 AM •
Intertherm...
•
Answered
on Dec 12, 2011
•
190 views
Intertherm furnace will not ignite the board
Hi, you will have a chart glued to a panel with a list of codes per flashes telling you what to check with 4 flashes. Read this and get back to me on what is is telling you.Robert Horton
12/2/2011 3:56:51 PM •
Intertherm...
•
Answered
on Dec 02, 2011
•
323 views
I have a Intertherm MAC 1175. The pilot light was
Hi, sounds like the MGV is not shutting off all of the way/ That would be the only reason gas would continue to flow, even on a small scale. If this keeps up, change that valve!! Do not take it apart, never! Good luck,Robert HortonPS MGV ( Main gas valve )
12/2/2011 3:52:04 PM •
Intertherm...
•
Answered
on Dec 02, 2011
•
619 views
My furnace heats up and then shuts down not
Your furnace is shutting off on the high limit switch because of this. You are having a problem with the blower motor. You need to check for power from the wires on the board that feeds the motor. If you have voltage, and your run capacitor is good, you have a faulty blower motor. If its a fan relay, the fan would start and run all of the time. Check power to motor right after furnace shuts the burners off.Robert Horton
12/2/2011 3:46:04 PM •
Intertherm...
•
Answered
on Dec 02, 2011
•
338 views
Intertherm mmha070
Hi, did he bypass the high limit to see if it was bad? Sounds like you are getting false codes and you have a problem in your module or main board, which ever you have. The way it is acting, saying the high limit is open but the tech says its not, I would change the board.Shastalaker7
12/2/2011 3:38:40 PM •
Intertherm...
•
Answered
on Dec 02, 2011
•
403 views
Not finding what you are looking for?