20 Most Recent AOpen F2705 17" LCD Monitor Questions & Answers


go to control panel ,display, monitor , move the slide for pixels , apply and ok if you want bigger , there is a tick box as well 100%,150% adjust that as well

AOpen F2705 17"... • Answered on Apr 27, 2017


driver not usually required; what model? You wont get a response without a model number, this is your 2nd post

AOpen F2705 17"... • Answered on May 14, 2014


bad lamps you may check your monitor ccfl maybe or the inverter.

AOpen F2705 17"... • Answered on Jun 03, 2013


yes there is. maybe blowned. test if it have continuity, if bad, change it. if its still the same your problem its other.

AOpen F2705 17"... • Answered on Jun 03, 2013


The problem is in the power supply board, one or two capacitors become open and sometimes leave a slight puff on the top killing power to the monitor.

AOpen F2705 17"... • Answered on Mar 17, 2012


Might not getting any signal from the source ,you will have to try your cpu else where with same vga cable to figure out whether its your monitor or your cpu tower.

AOpen F2705 17"... • Answered on Sep 02, 2011


A number of things can cause "No Signal" on a monitor

1) Check the cable between the monitor and PC is properly connected
2) If the PC has more than one display port try changing the display port the monitor is plugged into
3) Try an alternative cable between the monitor and the PC
4) Check that the correct input is selected on the monitor

AOpen F2705 17"... • Answered on Dec 16, 2010


Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague

http://www.badcaps.net

AOpen F2705 17"... • Answered on May 16, 2010


Please try it on another PC, if it still does not work, then read below:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://www.badcaps.net
http://en.wikipedia.org/wiki/Capacitor_plague

AOpen F2705 17"... • Answered on Apr 15, 2010


Most common failure in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, falied inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what goes wrong: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further.

AOpen F2705 17"... • Answered on Mar 29, 2010


Yes your monitor will work with windows 7 it has a generic driver for monitors installed into the system.

If your monitor has a driver cd for it, for more cababilities found on the monitor you may have to visit there web site for updates. Other than that your monitor should work fine with no problems.

AOpen F2705 17"... • Answered on Mar 23, 2010


I would say that the computer is trying to use a display resolution that the monitor is incapable of displaying. You may have to lower the resolution from the PC before you get a picture. Make sure you install the correct drivers for the monitor onto the new computer and use a different monitor to adjust the display resolution to a level that the monitor is capable of displaying.

AOpen F2705 17"... • Answered on Dec 15, 2009


You will nee to find out the frequency range of your flatscreen whick should be in the book that came with it. Also, try pressing f8 and see if u can see the menu that comes up, if u can see it then select safemode and see if it will boot like that. If so, install the correct driver for the flatscreen.
your drivers are at this link.

http://download.aopen.com.tw/userdownload_List.aspx?RecNo=10160&Model=1425

AOpen F2705 17"... • Answered on Feb 26, 2009


May i know, is it a crt monitor or lcd monitor? If it is a crt monitor, then you can try to check the dry joint on te pcb board especially primary and secondary power supply. After that check the FBT with blue ring tester & cap meter to check their HV cap value.

If it is a LCD Monitor, please check on inverter board and the ccfl lamp too. Please check all the electrolytic cap on lcd monitor pcb board for low esr ohm with blue esr meter. Below is some usefull link for repair lcd monitor and crt monitor:

1) www.FastRepairGuide.com
2) www.fastrepairguide.com/recommend/lcd-monitor-repair/

Hope this help.

To your success,
Kent

AOpen F2705 17"... • Answered on Dec 05, 2008

Not finding what you are looking for?
AOpen F2705 17" LCD Monitor Logo

32 questions posted

Ask a Question

Usually answered in minutes!

Top AOpen Computers & Internet Experts

Cindy Wells

Level 3 Expert

6259 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Joe Goldman
Joe Goldman

Level 2 Expert

337 Answers

Are you an AOpen Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

AOpen Computers & Internet

  • AOpen Computers & Internet

Most Popular Question

monitor will not come

  • Computers & Internet
Loading...