20 Most Recent Breville Die Cast 800ESXL Espresso Machine - Page 9 Questions & Answers

If the heating element in your espresso machine does not heat and your thermostat is working, then check the thermal fuse. The thermal fuse works to prevent overheating by blocking power from getting to the heating element and works with thermostat. If it fails to work, then it is best to replace your thermal fuse.

How to Repair Your Espresso Machine When it Doesn't Heat

and also

Why Breville Espresso Machine Not Heating Up

howtofixit.net https://howtofixit.net > why-breville-espresso-machine... Aug 4, 2022 - Your Breville Espresso Machine may not be heating up because of a damaged or clogged heating element. The problem could also be due to a blown ... ‎Incorrect Settings · ‎Clogged or Damaged Heating... · ‎Faulty Thermostat

Safety Tip: To prevent any potential mishaps, ensure sure your grinder is fully off and unplugged before using it. Also, if you haven't used it in a while, make sure it's cool to the touch. Let the Bean Hopper open. Take off the bean hopper from your grinder's top. This is going to reveal the top burr. Take the Upper Burr Carrier Off: An upper burr carrier is usually used to hold the top burr in place. It is necessary to take out the upper burr carrier. Depending on the kind of your grinder, the precise procedure may change, but generally speaking, it entails undoing a few screws or tabs that secure it. In general, follow these steps: a. Check the upper burr carrier for any visible screws or tabs. Usually, they're close to the edges. b. To release the tabs or loosen the screws, use the proper equipment (usually a screwdriver). To prevent breaking the grinder, use gentleness. c. After the upper burr carrier is released from its locking mechanism, carefully pull or slide it out. Lift Out the Top Burr: The top burr can now be removed after the upper burr carrier has been taken out. The burr might be secured in place by tiny clips or notches, so proceed with caution and gentleness. Clean and Maintain: After removing the top burr, you can give the grinder and its parts a thorough cleaning. Make sure you adhere to the cleaning and maintenance guidelines provided by the manufacturer. This often entails cleaning the grinder's parts, brushing off coffee grinds, and correctly reassembling it. Reassemble: Carefully put the grinder's parts back together in the opposite order after cleaning. Verify that the upper burr carrier is correctly positioned and that all screws and tabs are firmly in place. Plug in and Test: After the grinder has been put back together, plug it in and make sure it is operating properly.

They need dealer service every 6 to 9 months. They don't tell you this when you buy them.

Question edited for clarity.I deleted the AI Answer Bot Answer twice if you got a notification someone had answered. The answers are wildly generic and not specific to the device as mine are!The inner plastic cap stays on. Here is the manual opened to that page.https://www.manualslib.com/manual/1360350/Breville-Btm600.html?page=4#manualhttps://www.breville.com/ca/en/products/tea/btm500.html...

Breville Coffee Machine Service & Repairs

The Kenwood Guys https://thekenwoodguys.com > products > brevillecoff... The Kenwood Guys - Cape Town. Pickup available, usually ready in 2-4 days. 8 Cloete Street Bothasig Cape Town Western Cape 7441. South Africa. +27212049210.

To clear a stone from the breville/sage grinder first remove the hopper and vacuum any beans out of the top of the grinder, then using a paint brush and the vacuum cleaner clear small debris from inside the grinder cone. Hopefully you will see the stone , you may need to use a torch. Now using a pair of pliers turn the top of the inner grinder cone anti clockwise (that's not the silver nut but the top of the cone itself) hopefully this will free the stone enough to pop it out with a small screwdriver or piece of very stiff wire. If this doesn't work you may need to contact breville/sage as its unlikely you will be able to remove the exterior cone sleeve without damaging it, and if the stone has reached the fine burrs below the coarse feed burr it may have caused serious damage. Otherwise refill with a few beans and check its working ok.

I have an Antony Worral Thompson breville CM2 espresso cappuccino maker with out any instructions. can nor find any anywhere on line

Maybe you are using larger cups than suggested .......

It is covered in this link https://www.google.com/search?q=Breville+xl+830+drain+leaking+in+bottom+pan ..

http://www.fixya.com/support/t26840034-knob_our_breville_cafe_roma_become_very https://www.centredurasoir.com/media/products-files/ESP8SXL_User_Guide.pdf

I am having a similar problem ( I say similar as I can't tell you what might yours be till you open the machine; if your warranty is over). Unplug and take the top off you will see the heating block and a bunch of electrical stuff (don't get overwhelmed, just don't touch it as your better safe than sorry). Now try and see if you can locate any cracks or calcium that show the water is leaking from. You will see two pipes coming off fitting on a black square block ( the pump) one is big and feeds the coffee water and the other steam. In my case the steam input is leaking, I had to run the machine to see it. Happened after a cleaning that should have been done months ago.... (I don't drink coffee often, but the Wife does and is lazy). So the way to fix is still in the works on my end. As you need a seal but not sure what I will use, maybe an rtv silicon (not sure that is food grade though and prefer not giving higher odds of Cancer to the better half).

possible bad pump or calcium build up inside

warranty

Set the timer and the clock , and put the clocks back one hour tomorrow .

Try descaling it. See if that helps.

Adjust water (more) and bean quantities (less), see here: http://brevilleusasupport.com/bes980xl/care-and-use/menu-functions/