20 Most Recent Maytag Neptune Washer Questions & Answers

0helpful
2answers

Bearing noise

rear bearing is pressed into outer drum never changed bearing only usually requires entire drum replacement instead..also shaft on rear of inner basket is probably scored bad and needs replacement too
10/14/2020 11:28:10 AM • Maytag Neptune... • Answered on Oct 14, 2020
0helpful
1answer

NEPTUNE WASHER BEEPS,,WANT TURN OFF OR START

When door locks like that next time. If you remove the top of the machine. Reach down inside on left side. There is a small wire cable that you pull up on. Will manually unlock the door. Then plug power cord in to wall. Power it on let it go through reset cycle and it will work properly again. However if you can't reach the latch through the top. Tilt washer forward and reach up from the bottom. If you get an F1 code it's low water pressure.
12/31/2019 10:49:27 PM • Maytag Neptune... • Answered on Dec 31, 2019
0helpful
2answers

Washer started and then stops mid cycle

Try unplugging it for a minute and plug back in, that should reset it.
9/24/2018 6:27:23 PM • Maytag Neptune... • Answered on Sep 24, 2018
0helpful
1answer

What does f1 E7 errors mean on neptune washer

There may be a problem with the Appliance Control Board, or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven for one (1) minute to ensure the error code does not display again.
4/25/2018 3:19:33 PM • Maytag Neptune... • Answered on Apr 25, 2018
0helpful
1answer

Mhw2000 rinse and spin cycle not working

It won't spin if it cannot pump out ALL of the water. Check the outlet pump for obstructions and clear. Check pump to see if its pumping.
6/23/2017 10:08:33 AM • Maytag Neptune... • Answered on Jun 23, 2017
0helpful
1answer

My washing machine door will not unlock. I have a

some doors will release if given a hard bang where the interlock is...at the door catch......... cheers
5/28/2017 4:48:40 PM • Maytag Neptune... • Answered on May 28, 2017
0helpful
2answers

On my Maytag Neptune MAH-3, the water is running non-stop

check plastic hose out side of tub to pressure switch
if ok replace pressure switch
6/29/2015 3:15:21 AM • Maytag Neptune... • Answered on Jun 29, 2015
0answers
0helpful
1answer

I have a 14 year old Neptune that run great except now no hot water.

There's a fill valve combination on most washers. On the simpler, cheaper models they're simple to change. It's where the hoses connect, it's usually plastic, and there is a hot and a cold valve in the assembly. Hot opens for hot water, cold opens for cold water, and both open for warm water. apparently the solenoid valve on the hot water side has failed and the unit needs to be replaced.
5/23/2014 7:04:34 AM • Maytag Neptune... • Answered on May 23, 2014
0helpful
1answer

Whybdoes water remain in machine at end of wash?

If the drain pump malfunctions...or is clogged then it will not empty within the time cycle and the unit will time out. the pump in at the bottom of the machine
5/23/2014 7:00:32 AM • Maytag Neptune... • Answered on May 23, 2014
0answers
0helpful
1answer

Water flows out door while in use

Check the door gasket/seal for damage. Check to see if the door's mounting brackets are loose by lightly moving the door up/down. Also check the level of the machine to ensure that the frame is not twisted.
4/22/2014 3:18:54 AM • Maytag Neptune... • Answered on Apr 22, 2014
Not finding what you are looking for?
Washing Machines Logo

468 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Brad Brown

Level 3 Expert

19106 Answers

Steve

Level 3 Expert

3290 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Neptune Maytag

  • Neptune Maytag

Most Popular Question

14 year old neptune run great except now

  • Washing Machines
Loading...