20 Most Recent Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher Questions & Answers

0helpful
1answer

Electrolux dishwasher leak detector light

This was a good answer. It reset the error. But once we started the washer up again it threw the same error. Next step, remove it from the cabinet and check for leaks.
9/1/2017 11:13:55 PM • Electrolux 24... • Answered on Sep 01, 2017
0helpful
1answer

Maytag model MDB5130AWW - not cleaning

Is the top arm spinning freely?
4/7/2017 3:07:10 AM • Electrolux 24... • Answered on Apr 07, 2017
0helpful
2answers

Just installed and ran for

Hello. I also own the Electrolux EWDW6505GS--0 {24'' Built-In Dishwasher with Wave-Touch® Controls} On two occasions I have had the "Error 04 Drying Damper - Drying damper not operating" In each case, I found the plastic 'ring nut' RETAINER in the upper right top of the machine had come loose. I simply unscrewed the retainer, wiped the area down, and re-screwed the ring on hand tight. Sincerely, Patrolcats Here is a picture of the retainer; just-installed-ran-clmz3n1br0lqygylhtdn2fhc-4-0.jpg A new retainer part (if it is broken) may be ordered here at the RepairClinic; Electrolux Dishwasher Retainer 154622601 Use & Care Guide http://manuals.electroluxusa.com/prodinfo_pdf/Kinston/154671101en.pdf Service Data Sheet http://manuals.electroluxusa.com/prodinfo_pdf/Kinston/154676601.pdf
1/4/2015 5:13:46 AM • Electrolux 24... • Answered on Jan 04, 2015
0helpful
2answers

How do i find the leak sensor on my electrolux dishwasher?

Good Afternoon Friend, I understand you want to know where the leak sensor is on your Electrolux dishwasher, model# EDW5500DSS. Typically the leak sensor will be located underneath the tub area. There are no diagrams that show exactly where the sensor is located. I suggest contacting your local authorized technician for further assistance. They have been trained on your appliance and will be able to best assist. Hope this is helpful. -Best Regards- WP
6/27/2014 4:55:37 PM • Electrolux 24... • Answered on Jun 27, 2014
0helpful
1answer

ALL LIGHTS BLINKING

There is an older post that may help: http://www.fixya.com/support/t2062601-electrolux_dishwasher_all_lights
6/18/2014 3:06:16 AM • Electrolux 24... • Answered on Jun 18, 2014
0helpful
1answer

What is error code "02"

Getting an Error Code 2 on your dishwasher, means there is something going on with the turbidity sensor. This is the sensor that determines how dirty the water is which in essence determines how long the cycle will run. What you can try to do is to reset the appliance for 30 minutes. You will do this by cutting the power at the circuit breaker and leaving it off for no less than 30 minutes. Try running the cycle again and if you are still receiving the Error Code 2, I would recommend contacting the manufacturer for further assistance.
6/6/2014 4:38:07 AM • Electrolux 24... • Answered on Jun 06, 2014
0helpful
1answer

What is error cod "02"

Did you see this post? That's all I could find relating to that code. http://www.fixya.com/support/t22713255-error_code_02_ewd6505gso
6/6/2014 3:28:09 AM • Electrolux 24... • Answered on Jun 06, 2014
0helpful
1answer

Eidw6105gb1 dishwasher lights blinking took toe plate off the wash pump light is on but the unit washes great cound that control be sensing a but wash pump even if the pump is working?

Good Afternoon John, I see that your Electrolux dishwasher, model# EIDW6105GB1, has all the lights blinking and is revealing the wash pump light. This could just be a false error and would need to be cleared or it could mean that the wash pump is going bad. You can try resetting the appliance, by cutting the power at the circuit breaker for 20-30 minutes. When power is returned, start a cycle. If the lights are still flashing and revealing the wash pump light, I suggest either contacting the manufacturer or maybe a local authorized dealer. Hope this helps. -Best of luck- WP
3/27/2014 7:00:32 PM • Electrolux 24... • Answered on Mar 27, 2014
0helpful
5answers

Electrolux dishwasher all lights blinking and wont

Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be good to go. I have no idea why this is not in the instruction manual. A common one is that there us a leak that the dishwasher has detected, normally in the drain pipe.
3/26/2014 10:34:29 PM • Electrolux 24... • Answered on Mar 26, 2014
0answers
0answers
0answers
0helpful
1answer

Error code 02 ewd6505gso

Sandra Lawson, Getting an Error Code 2 on your dishwasher, means there is something going on with the turbidity sensor. This is the sensor that determines how dirty the water is which in essence determines how long the cycle will run. What you can try to do is to reset the appliance for 30 minutes. You will do this by cutting the power at the circuit breaker and leaving it off for no less than 30 minutes. Try running the cycle again and if you are still receiving the Error Code 2, I would recommend contacting the manufacturer for further assistance. -Best Regards-
1/9/2014 6:13:19 PM • Electrolux 24... • Answered on Jan 09, 2014
0answers
0answers
Not finding what you are looking for?
Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher Logo

Popular Tags

101 questions posted

Ask a Question

Usually answered in minutes!

Top Electrolux Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3054 Answers

Cindy Wells

Level 3 Expert

6699 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you an Electrolux Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Electrolux Dishwashers

  • Electrolux Dishwashers

Most Popular Question

just installed ran

  • Dishwashers
Loading...