3Com NBX V3000 IP Phone - Answered Questions & Fixed issues

The phone password has to be reset on the phone system (by the Administrator), not the phone. If you purchased phones and added them to the system, then those extensions wouldn't have passwords on them if they were newly added to it. If you purchased the entire system and phones then you can reset the phone passwords under "system maintenance", "password administration".

This does happen occasionally but is not a typical thing. This means that you have either lost network access to the system or a service on the system has stopped. The system will have to be rebooted to get things going normally again. The preferred method (since you can do it through netset) is to connect to the console port with a DB9 straight through serial cable and open hyperterm or putty and connect to it at 9800, 8, 1 none settings. Hit ctrl r and the system will reboot. if you don't have a serial cable then you are forced to pull the power or switch it off and then back on. CAUTION: you risk a database corruption every time the system loses power without closing the database properly (netset or ctrl r through the console) so do this as a last resort. Also, the system will do a disk scan (except V3001) and will take 15 to 45 minutes to complete before the system will start to function again. DO NOT UNPLUG IT AGAIN WHILE IT IS DOING A DISK SCAN! You can tell if it is doing the scan by looking at the S1 and S2 lights on the Call Processor. During a disk scan, they will be alternating back and forth (like police lights). Wait for it to complete and try netset again. I recommend doing a fresh reboot through netset after it comes back up just to be sure it's a fresh clean boot.

Yes, press the feature button and then enter 889. This will restrict the NBX system from sending out your Caller ID information for all calls. You will have to disable this by doing the same thing if you want to get your outbound caller ID back. Feature 890 will restrict the NBX system from sending out your Caller ID information for this call only.

There is most likely another device on the network with the same IP as the phone system. You can check this by un plugging the link to the phone system (after hours of course) and then pinging the IP of the phone system. If you get a reply while the link is disconnected then you know there is a duplicate IP on the network. You can use your server to try to identify the device or use a IP scanner like NetScanTools to ID it. You could also try changing the IP address of the phone system and see if you have the same problem.

Reboot the phone system (through the browser) and this should take care of it. There are limited voicemail ports and sometimes they get put on hold and can't be released. I have seen it a lot. some versions of software can clear this but a reboot will take care of it.

This is a Internet Explorer issue. If you use it in "compatibility view" it will show all users when you click on show all users. Otherwise use google chrome or firefox.

Ok it is may be do you to system is old needs up to date , so that the video may not have downloaded completely from the source web portal. The media player present in your handset is outdated.

A very simple solution to r epairing all by yourself is getting help from handbooks, they're very detailed and complete in every way so for me it was my b est source to repair one of the top sites for this is https://big-manuals.com/

Time for a new mouse! I’m happy to help further over the phone at https://www.6ya.com/expert/joshua_ac64e182ed26f66d

I don't know anything about these units, nor do I have time to source any docs for you, but maybe you can try connecting a PC directly to the port your patch panel is connecting the the switch from, you can at least see if that port is working. My next and only other suggestion is to invest in a "LAN cable tester". In my area, you can find cheap ones for U$20. The tester will allow you to check connectivity between any two ports, and allows you to test both patch links and individual CAT5/6 cables. Good luck!

notify the police dept / person handling the case and let them know about the face book information

Use a brute force password solver or at best do a reset

Fixya offers advice to DIY people. With something like you are talking about, it would not be easy because of parts, and manufacturing processes. Also it might cost more to have it repaired than to get a new one.

Hi, I hope this link is waht you need. http://www8.hp.com/us/en/support-search.html?tab=1#!=&qryterm=3com 40 0483 001 ethernet&search_searchtype=s-002 If not please the exact model of your device. Good luck

1 Remove power from the Gateway. 2 Disconnect all your computers and the cable/DSL modem from the Gateway router. 3 Using a straight through Ethernet cable, connect the Ethernet Cable/DSL port on the rear of the Gateway to any one of the LAN ports. 4 Re-apply power to the Gateway. The Alert LED will flash as the Gateway starts up, and after approximately 30 seconds will start to flash more slowly (typically 2 seconds on, 2 seconds off). Once the Alert LED has started to flash slowly, remove power from the Gateway. 5 Remove the cable connecting the Cable/DSL port to the LAN port, and reconnect one of your computers to one of the Gateway LAN ports. 6 Re-apply power to the Gateway, and when the start-up sequence has completed, browse to: http://192.168.1.1 and run the configuration wizard. You may need to restart your computer before you attempt this. 7 When the configuration wizard has completed, you may reconnect your network as it was before Here on page 85 of the manual 3Com 3CRWE53172 User Manual Forgotten Password And Reset To Factory...

For 3Com that would mean a 3100 series or 3500 series phones. The 3100 series phones are for NBX and VCX phone systems and the 3500 series phones are for VCX only. Both are also SIP compliant.

Here is the standard pinout for a console port on a router to seriel port for computers

If I remember correctly, there is a tiny hole at the back or on the side. Press a paper clip into it. The switch should do a full reset and then reboot. If its just locked up, I would switch off at the power for 15 mins and try let it do an auto restart itself. Do this before you go doing a full button press reset as you may lose any or all updates the switch has had loaded into it.

Are you able to remove the card from your PC? and read the model on it? Are you able to find your motherboard/computer model? use the motherboard/computer model to find what model of card is on it. Once you have the nic model search for a driver.

From Digium Mailing List: 3Com 3100 series phones do not support SIP with non-3Com systems. They have a basic boot loader which must download code from a 3Com NBX or a 3Com VCX system. If you don't have either of these, then you won't get runtime code on the phone, thereby making it impossible to use the thing with Asterisk. Asterisk Users 3Com Phones