20 Most Recent Western Digital WDH1NC15000N 1.5tb Rj-45 Network Usb Network Hard Driv - Page 3 Questions & Answers

If you will Google search the following, the WD drives that will work in this computer are shown: western digital 9.5mm 750GB SATA 5400RPM hard drive

The format on a disk, will not be relevant of recognition via an USB connector. To connect a drive via USB, the computer must have the correct driver for the hardware you are connecting. Be sure you connect the HD coerce to the external harness and make sure it is supplied with the correct voltages. When you connect a working system on the USB connector and the drive does not have a format, the computer will see that and ask you if it should format the drive.

They are probably still there if you have not written any new files to the drive. read this link http://www.tomshardware.com/forum/285728-32-data-back-formatted-drive-recovery

Check windows disc management to see if the drive is mounting.

Guwahati Acer India (Pvt) Ltd. H.No.101, Ground Floor, Opposite City Heart Hospital, Near Bihutoli, Rajgarh Road, Guwahati - 781 007. Tel: +91-9854092884. http://www.acer.co.in/ac/en/IN/content/contacts or

I could not find any information about WD28001032. Are you sure that this is the correct model number for your HDD?

Not sure what your question is, but this may be helpful:

Read page 41 of the manual and you will learn how to change your password: http://www.wdc.com/wdproducts/library/UM/ENG/4779-705063.pdf

Buy a new external hd enclosure and reuse the hd from the failed enclosure. Hard drive enclosers are cheap BTW. Try newegg!

Could be a malfunctioning drive interface within the hard drive.

Sorry, no help for you after doing both a roll back and a reformat. This is what has driven professionals to a 3-2-1 backup solution. 3 backups - 2 onsite(two different parts of the house, business) - 1 off-site. Then you can restore from a backup. Otherwise, restore from optical disk or restore partition(if you didn't format it). Good Luck.

If the BIOS doesn't see the drive, you are usually out of luck. You may have 1 and only 1 chance to get data off the drive. wrap in a small hand cloth.place in a ziplock sealed within another sealed ziplock. leave in the freezer overnight. Then the next day attempt to read the drive. Occasionally, this cooling, allows the drive to be read. IF so, get the data off immediately because as soon as the drive "thaws or warms" you may not be able to read it. The trick usually only works once, as it introduces condensation. THIS is a last ditch effort before giving up.

Hello Hector, your motherboard supports: 2 x Ultra DMA133/100/66 devices(IDE) 4 x Serial ATA2 devices (SATA) IDE is somewhat antiquated at this point but is supported, I would recommend using the SATA ports instead due to higher performance. Drives of this type can be purchased at any computer shop, most big box stores and any online parts store.

I have a DROBO which I am trying to recover with DiskWarrior. When I connect the DROBO and try to run DiskWarrior, I get an error -36 "hardware failure". I can hear the DROBO doing "stuff". If I wait several hours until the DROBO is quiet, then DiskWarrior doesn't get the error, and I can try to recover it. Scratched my head over this for a while, so figured I would post the solution in case anyone has the same problem. All the forum posts are about dead disks. My disk isn't dead, it just has a sick filesystem, as proven by the fact that if I wait long enough, DiskWarrior can try to do something with it. The disk activity was a clue. I suspected that TimeMachine or something else on the mac is trying to fsck the file system in preparation for mounting. Unfortunately that takes HOURS on this large volume full of time machine backups. So opened Terminal and typed: ps -ef ' grep fsck_hfs and there was the culprit: 0 67332 18 0 6:26am ?? 1:02.06 /System/Library/Filesystems/hfs.fs/Contents/Resources/../../../../../../sbin/fsck_hfs -y /dev/disk5s2 To kill it, type kill followed by the second number from the left, in this case: kill 67332 The disk activity stops, and you can then run DiskWarrior.

then western digital needs to know let me give you number 1 (800) 275-4932- WD support help desk

It may because you either deleted the drive and did not re assign a drive letter to it, or it may be due to format, when you using Windows OS, your hard disk should be either in FAT or NTFS format, if you have linux as secondary os, you may have accidental format the drive with linux OS. Try changing the format to NTFS or FAT. Try and reply back

Try some of the free data recovery software to see if they can read it. Recuva, PhotoRec and other decent free programs as a start.

Replace the power cable and data cable. If still no help, the drive is dead and needs to be replaced.