20 Most Recent Lexmark Refurb X1185 All-in-One USB Printer/Scan/Copy - Page 7 Questions & Answers


you printe molde

Lexmark X Office... | Answered on Sep 24, 2012


Normally printer heads are located near to and slighty above the ink cartridges.

Lexmark X Office... | Answered on Jul 02, 2012


Please note that once a Lexmark cartridge is refilled, it can no longer register its ink level.
Also, Lexmark does not recommend the use of refilled, re-manufactured or clone cartridges. You might not get the print quality you expect from the ink that is specially formulated by Lexmark.

Lexmark X Office... | Answered on Feb 22, 2012


Leading cause of paper jams is debris / foreign objects that accidentally fell into the paper feed area. Please try this approach to fix the problem:

  1. Remove the sheets of paper from the feeder.
  2. Grab a flashlight and look inside the feeder for any debris or foreign objects.
  3. If you're willing and physically able, you may also carefully turn the printer over. Any debris should just freely roll out from the feeder.
  4. If feeder is clear, place the printer on the table. Open the printer cover and remove the cartridges.
  5. Check the cartridge area for any obstructions in the paper path.
  6. Close the printer cover.
  7. Re-brick your printer by pulling out the power supply - the black box where the power cord is plugged into. Re-plug after 30 seconds.
  8. When the printer turns on, reinsert the cartridges and load some paper. Try to print again to verify that the problem is fixed.
If that doesn't help, try to re-seat the cartridges by removing and re-inserting them into the printer. Make sure they are properly seated and secured.
I hope this helps.

Lexmark X Office... | Answered on Feb 17, 2012


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer (if USB connected)> reboot your pc > unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer (if USB connected). Then try to print again once the computer fully recognizes the USB connection or when the WiFi light on the printer turns solid green (if WiFi connected.).


If that doesn't help, try the steps below:

  1. Disconnect the USB cable connecting the printer from your computer.
  2. On your computer, go to Control Panel > Printers and Faxes.
  3. Delete the Lexmark print object.
  4. Reboot computer.
  5. Re-brick your printer by pulling out the power supply - black box where the power cord is plugged into on the back of the printer, and re-plug after 30 seconds.
  6. When the printer turns on, reconnect it to the computer.
  7. Wait until your computer fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, try to print a document to verify that the problem is fixed.

Lexmark X Office... | Answered on Feb 14, 2012


What is the model of your Lexmark printer? This will help us give you a more direct instruction on how to fix the problem you're currently experiencing.
Meanwhile, you can try to do a deep clean cartridge/printhead function on your printer to clear the cartridge/printhead nozzles from possible clogs and dirt.
If it's more on communication issue, a quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Frequently, issues are caused simply by a break in the signal sent from PC to printer or vice versa. Unplugging and re-plugging the printer allows the small amount of on-board memory on the printer to be cleared, with the result that the PC recognizes the machine properly. Programs continuing to run in the background of the operating system (OS) can cause the signal to be lost. Rebooting the PC ends all programs that may be running and makes a 'clean' start, allowing the signal to be detected.

Lexmark X Office... | Answered on Feb 10, 2012


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer (if USB connected)> reboot your pc > unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer (if USB connected). Then try to print again once the computer fully recognizes the USB connection or when the WiFi light on the printer turns solid green (if WiFi connected.).


If that doesn't help, try the steps below:

  1. Disconnect the USB cable connecting the printer from your computer.
  2. On your computer, go to Control Panel > Printers and Faxes.
  3. Delete the Lexmark print object.
  4. Reboot computer.
  5. Re-brick your printer by pulling out the power supply - black box where the power cord is plugged into on the back of the printer, and re-plug after 30 seconds.
  6. When the printer turns on, reconnect it to the computer.
  7. Wait until your computer fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, try to print a document to verify that the problem is fixed.

You may also try to update your printer driver by visiting the Lexmark website at http://bit.ly/AbnM39. Select your operating system, download and execute the file. After the install process, try to print again.

Lexmark X Office... | Answered on Feb 09, 2012


The problem could be due to a communication failure between one of the printheads (cartridges) and the All-In One (AIO) or by a short in one if the printheads. Please follow the steps below to identify and fix cartridge issues:

  1. Make sure the printer is on.
  2. Open the printer cover. The print cartridge carrier moves and stops at the loading position, unless the All-In-One is busy. Note: If the carrier does not automatically move to the center, turn off the printer or unplug the printer from the power source and then carefully slide the carrier to the center.
  3. Remove both cartridges from the carrier.
  4. Close the printer cover.
  5. Re-brick your printer by pulling out the power supply - black box behind the printer where the power cord is plugged in to, and re-plug after 30 seconds.
  6. When the printer turns on, reinsert one cartridge first. Close the printer cover and check for any errors.
  7. If no error appears, reinsert the other cartridge. Close the printer cover.
  8. Replace whichever cartridge is causing the error to appear with a new genuine Lexmark cartridge. Try to print a document again to verify that the problem is fixed.

Lexmark X Office... | Answered on Feb 09, 2012


If you're experiencing printhead error message on your Lexmark inkjet printer, make sure that your printer firmware is updated. A firmware update for your model addresses printhead issues. Please visit the Lexmark website to download and install the Lexmark Firmware Update. Select the corresponding firmware version for your model to start the download.
Should the printhead problem continue, please contact Lexmark Technical Support Center for additional assistance.

Lexmark X Office... | Answered on Jan 30, 2012

Not finding what you are looking for?
Office Equipment & Supplies Logo

14 questions posted

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

X Lexmark

  • X Lexmark

Most Popular Question

x1185 print

  • Office Equipment & Supplies
Loading...