Lexmark X2350 All-In-One InkJet Printer - Answered Questions & Fixed issues
Good day Sir, If paper misfeeds or skews, or multiple sheets feed or stick together, try the following solutions.
1. Load a smaller amount of paper into a printer and make sure you use paper designed for inkjet printers. The paper is not used or damaged.
2. Before loading paper the first time, squeeze and slide the paper guide to the left side of the paper support. Load the paper vertically against the right side of the paper support.
3. Adjust the paper guide until it rests against the left edge of the paper.
note: make sure the paper does not buckle when you adjust the paper guide. to avoid paper jams.
have a nice day!
on May 09, 2014
Computer will not show lexmark
Please post more details, and I'll see if I can help you. Is this a printer you just started using, or is it one you've been using for awhile, and your computer suddenly isn't recognizing it?
on Nov 20, 2012
No cd to install all
You don't actually need a cd to install the X2350. You can go to Lexmark's website in the support section and download the latest drivers and software needed for installation. The easiest way is to do a search for the X2350 in the search bar in the support section. Then it will ask which operating system you use. Select the operating system you use, and then it will list the downloads available based on your system. Download that to a place where you can find it on your computer (example: Desktop or My Documents). Once the download finishes, make sure your printer is powered on and the USB cable is plugged in. Then find the file you downloaded, double click on it, and the setup process will begin. This will install all of the necessary drivers and software so you can use the printer. Note: If it's the first time you've used the printer and connect it to the computer using the USB cable, then Windows will automatically try and find the drivers for you. I recommend cancelling this process and just using the drivers/setup that you downloaded from Lexmark's website.
on Sep 19, 2012
Try to re-seat the cartridges in the printer. Open the printer
cover > remove the cartridges > close the printer cover > re-brick you
printer by pulling out the power supply - black box behind the printer where
the power cord is plugged in, and re-plug after 10 seconds. When the printer
turns on, reinsert the cartridges and close the cover. Try to print a document
again to verify that the problem is fixed.
If that doesn't help, the problem could be due to a clogged print
cartridge nozzle. Please follow the steps below to fix print quality issues
with your model:
- On your computer, go to Start
- Go to Programs.
- Go to Lexmark 2600 Series
- Select Lexmark Solution Center.
From the Maintenance tab, select Clean to fix horizontal streaks.
Your printer will then print a page forcing ink through to clean the print
After printing the test page, try to print a document again to
verify that the problem is fixed.
on Apr 09, 2012
My Lexmark X2350 will not recognize a replacement ink cartridge
Lexmark does not recommend the use of refilled, re-manufactured or clone cartridges. You might not get the print quality you expect from the ink that is specially formulated by Lexmark and these type of cartridges often result to poor print quality and/or may cause damage to the printer itself. Reliability of these type of cartridges is very poor.
It is highly recommended to use genuine Lexmark cartridges for the most optimal output experience. Lexmark printers work best with genuine supplies.
on Jan 30, 2012
Printer will not turn on
If you are encountering power problems with your printer, please
go through the following checklist:
- Make sure the power cord is
plugged in securely and directly to the power outlet. Power surge
protectors can draw power away from the printer.
- Disconnect the power cord from
the power outlet and the back of the printer and then reconnect it.
- Check the power supply box (if
there is one) to see if it is warm or cold, as there could be a defective
power supply issue.
- If there is access to a
voltmeter, test the power supply to ensure that it registering the correct
amount of voltage (most Lexmark printers have a 30Volt output).
- Make sure the correct power
supply is connected to the printer.
For the problem where the cartridge carrier "slides back and forth", it could be due to the cartridges or the encoder strip
(transparent strip seated behind the cartridge carrier) has gotten loose from
its position. Please follow the steps below to identify and fix the problem:
- Open the printer cover and
remove the cartridges. Note: If the carrier does not automatically move to
the center, turn off the printer or unplug the printer from the power
source and then slide the carrier to the center for the loading position.
- Check the encoder strip and
make sure it is secured in its place.
- Close the printer cover.
- Re-brick your printer. Pull out
the power supply (black box where the power cord is plugged in at the back
of the printer) and put it back after 30 seconds.
- When the printer turns on,
reinsert one cartridge first. Close the printer cover and check for any
- If no error appears, reinsert
the other cartridge. Close the printer cover.
- Replace whichever cartridge is
causing the error to appear with a new cartridge.
- If no error appears, try to
print a document again to verify that the problem is fixed.
on Jan 23, 2012
How do i get my Lexmark X2350 Printer to send
Make sure that your default email program is correctly set on your computer.
A quick fix for most communication errors can be achieved by
resetting the printer and/or rebooting the PC. Simply disconnect the printer
from your computer (if USB connected)> reboot your pc > unplug and
re-plug the printer into the power source to reset it. When the printer turns
on, reconnect it to your computer (if USB connected). Then try to print again
once the computer fully recognizes the USB connection or when the WiFi light on
the printer turns solid green (if WiFi connected.).
If that doesn't help, try the steps below:
- Disconnect the USB cable
connecting the printer from your computer.
- On your computer, go to Control
Panel > Printers and Faxes.
- Delete the Lexmark print
- Reboot computer.
- Re-brick your printer by
pulling out the power supply - black box where the power cord is plugged
into on the back of the printer, and re-plug after 30 seconds.
- When the printer turns on,
reconnect it to the computer.
- Wait until your computer fully
recognizes the USB connection. To check, go to Control Panel > Printers
and Faxes. If you see a new Lexmark print object in the list, try to scan a document to verify that the problem is fixed.
on Dec 30, 2011
Keeps coming up Printer Driver is not installed
Try to re-install the printer driver on your computer. Before you install the new driver, make sure to uninstall the existing X2350 printer driver first. On your computer, go to Start menu > Programs > Lexmark X2300 Series folder > Tools > Uninstall. Reboot your pc when prompted.
When your computer turns on, visit the Lexmark website to download and install the
Lexmark X2350 Printer Driver on your computer. Select your operating system
> click on "FILTER" > click on the driver under Recommended
Downloads > download and execute the file. Simply follow the instructions on
your computer screen to complete the installation. Try to print a document again to verify that the printer is properly installed.
on Dec 30, 2011
My lexmark printer does not want to scan, when we
Make sure that you are pressing the Scan button and not the Copy button on the printer operator panel.
Try to re-brick your printer. Pull out the power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds.
on Oct 21, 2011
Not finding what you are looking for?