Ricoh Aficio Colour 3006 Color Copier - Answered Questions & Fixed issues

go to service program 5-810 ( sc reset) press on, turn off the machine an the turn on again. The service code should be gone, if it come back again check for a paper jammeed or wrapping the upper
fusing roller if this is not the case replace the thermistor;
Good luck
Vittorio

The SC 326 is -- 2nd laser synchronization error. Meaning, the 2nd laser synchronization signal cannot be detected by the main scan synchronization detector board even if the laser diodes are activated.

Basically your polygonal mirror motor unit is bad and needs to be replaced. You can replace the whole laser unit but that is expensive. When you replace the PMM unit, do so in a still air area -- as to not get anything in the unit. When you get the PMM unit -- contact me and I can walk you through the steps to replace.


The SC 452 is --- Transfer Belt Mark Detection Error. Once you fix the SC 326 error this one should be fixed also.

Nothing official listed for this error code. The SC6xx are electronics related errors.

If there is a HDD, try disconnecting it.

Otherwise, you may have a bad connection to the main electronics board (BCU) or a bad BCU.

user tools > admin > authentication settings and turn authentication off.

Verify your fusing lamp or thermofuse and replace it if necessary

If your circuit is correct, replace the power supply unit


Don't forget reset code :

Enter SP 5-810 (SC code

reset) and select "1". Then hold

down the Photo mode key and

the 7 key at the same time for

at least 3 seconds (this does

not require the main switch to
be turned off and on).

Make sure the paper is loaded properly in the trays. You can try using a different tray or not loading as much paper in the trouble tray.

SC387 Drum potential
error

Cause
· Uneven charge
· Worn drum
· Defective potential
sensor

Try the following
1. Clean the charge corona unit or replace the charge
corona wire and grid plate.
2. Reinstall the drum.
3. Replace the drum if necessary.
4. Replace the potential sensor.

Let me know if you need any more assistance

sc 452 is a thermistor error code for the fusing unit of the copier. Try pressing these buttons in sequence. (yellow key) (1).(0).(7) (red Clear/stop key) and hold the red key down for 5 seconds. When the 3 or 4 boxs appear, turn your copier on and off with the main power switch. If the error code comes back then contact the seller of your copier and ask for technical service.

Do you have the copier feature option installed?
It is most likely just a loose connection on the interface between the main printer unit and scanner section. Turn off main power (red button), and re-seat the connector.


Please let me know and rate solution :)

Hi There,

print out a page from windows paint program of cyan, magenta, and yellow. see which colors are incorrect. that will help you get closer to the problem area.

the drum also may not be screwed in all the way. remove it, and try putting it back in again.

Click here to download the manual.

This Code relates to color gamma error in the Yellow development. Possible causes Low toner density in the Y toner,Toner supply Y mechanism problem( not supplying enough toner),Laser exposure problem, image transfer problem. My suggestion would be to ensure you have toner in the cartridge( but by this time it has depleted the developer), and you will need to replace the development unit and possibly the drum Unit. My best guess would be the development Unit.

Munybuny

HI on the machine there should be a auto reduction enlarge all you need to do is press this place the original on the doc feeder and select the paper cassette in which the paper size you want the copy to be on. Once you have selected press the start button and then the reduction or enlargement is calculated for you.


Hope this helps and answers your question.

Thanks J

A3 size best is 1 90 to 100 grm

MP C2003 SC554-02 after change heating sleeve unit

Copytechnet https://www.copytechnet.com > forums > 138062-mp-c... sc 544-002 mpc4503 - Copytechnet Nov 1, 2014 Ricoh MP C5503 SC544-02 code - Copytechnet Aug 23, 2015 Ricoh C5503 - SC554 - Copytechnet Feb 14, 2017 mp4054 - SC554-02 after parts test from another - Copytechnet Mar 2, 2022 More results from www.copytechnet.com Missing: Aficio ‎' Show results with: Aficio

How To Cancel Sc544-02/Sc554-02 With A New Unit ...

ManualsLib https://www.manualslib.com > ... > Field service manual Ricoh MET-C1 Manual Online: How To Cancel Sc544-02/Sc554-02 With A New Unit Detection Fuse. • To cancel SC544-02/554-02, it is necessary to replace the ...

How to reset error code SC554-02 Ricoh MPC3503

CORONA TECHNICAL https://www.coronatechnical.com > 2020/06 > sc554-02-... Jun 3, 2020 - The fault SC554-02 occurs in the fusing unit, which reaches the end of life. You cannot reset unless you change the fuser unit or the Pico fuse. ..

Here is the Error

Error Codes > Ricoh > MPC3003SP > Code SC324-05

PrintCopy .info https://printcopy.info > brand=Ricoh > code=SC324-05 Code: SC324-05 · Description: Development motor: CMY: Lock Lock signals are observed at 2 sec intervals during motor ON, and a High level is detected at least 20 ...

MP C4503 sc324-05

Copytechnet https://www.copytechnet.com > forums > 137666-mp-c... Mar 28, 2019 - A motor lock error does not mean the motor is locking. It means the the motor is not able to achieve the proper constant speed, ie speed lock. Ricoh MPC 3503 et all Drum/Developer Unit with SC-324-05 ... Aug 3, 2019 MP4000/5000 SC324 Errors - Copytechnet Nov 1, 2010 error code sc 324 - Copytechnet Jan 16, 2015 MP 4000 SC324 error - Copytechnet Sep 5, 2019 More results from www.copytechnet.com ..

This is usually a software issue from a setting either from the printer properties, or from the the program printing like Outlook or a Website.

Question edited for clarity, full name, add spaces and CAPS. https://www.google.com/search?q=Ricoh+Pro+L5160+SC293-03 ..

You can use following website for troubleshooting problem. Chapter contents - Hardware Guide (ricoh.com)

You either have a torn ITB belt or a faulty ITB belt unit. If this is not your problem then you could have a faulty ID sensor or a faulty PCU that is causing your Process Controll to fail and generate the SC285.