20 Most Recent Ricoh Aficio Colour 3006 Color Copier Questions & Answers


go to service program 5-810 ( sc reset) press on, turn off the machine an the turn on again. The service code should be gone, if it come back again check for a paper jammeed or wrapping the upper
fusing roller if this is not the case replace the thermistor;
Good luck
Vittorio

Ricoh Aficio... | Answered on Mar 10, 2013


The SC 326 is -- 2nd laser synchronization error. Meaning, the 2nd laser synchronization signal cannot be detected by the main scan synchronization detector board even if the laser diodes are activated.

Basically your polygonal mirror motor unit is bad and needs to be replaced. You can replace the whole laser unit but that is expensive. When you replace the PMM unit, do so in a still air area -- as to not get anything in the unit. When you get the PMM unit -- contact me and I can walk you through the steps to replace.


The SC 452 is --- Transfer Belt Mark Detection Error. Once you fix the SC 326 error this one should be fixed also.

Ricoh Aficio... | Answered on Sep 23, 2011


Nothing official listed for this error code. The SC6xx are electronics related errors.

If there is a HDD, try disconnecting it.

Otherwise, you may have a bad connection to the main electronics board (BCU) or a bad BCU.

Ricoh Aficio... | Answered on Sep 08, 2011


user tools > admin > authentication settings and turn authentication off.

Ricoh Aficio... | Answered on Jul 28, 2011


Verify your fusing lamp or thermofuse and replace it if necessary

If your circuit is correct, replace the power supply unit


Don't forget reset code :

Enter SP 5-810 (SC code

reset) and select "1". Then hold

down the Photo mode key and

the 7 key at the same time for

at least 3 seconds (this does

not require the main switch to
be turned off and on).

Ricoh Aficio... | Answered on Jul 08, 2011


Make sure the paper is loaded properly in the trays. You can try using a different tray or not loading as much paper in the trouble tray.

Ricoh Aficio... | Answered on Oct 26, 2010


SC387 Drum potential
error

Cause
· Uneven charge
· Worn drum
· Defective potential
sensor

Try the following
1. Clean the charge corona unit or replace the charge
corona wire and grid plate.
2. Reinstall the drum.
3. Replace the drum if necessary.
4. Replace the potential sensor.

Let me know if you need any more assistance

Ricoh Aficio... | Answered on Jun 08, 2010


sc 452 is a thermistor error code for the fusing unit of the copier. Try pressing these buttons in sequence. (yellow key) (1).(0).(7) (red Clear/stop key) and hold the red key down for 5 seconds. When the 3 or 4 boxs appear, turn your copier on and off with the main power switch. If the error code comes back then contact the seller of your copier and ask for technical service.

Ricoh Aficio... | Answered on Oct 20, 2009


Do you have the copier feature option installed?
It is most likely just a loose connection on the interface between the main printer unit and scanner section. Turn off main power (red button), and re-seat the connector.


Please let me know and rate solution :)

Ricoh Aficio... | Answered on Apr 17, 2009


Hi There,

print out a page from windows paint program of cyan, magenta, and yellow. see which colors are incorrect. that will help you get closer to the problem area.

the drum also may not be screwed in all the way. remove it, and try putting it back in again.

Ricoh Aficio... | Answered on Dec 20, 2008


This Code relates to color gamma error in the Yellow development. Possible causes Low toner density in the Y toner,Toner supply Y mechanism problem( not supplying enough toner),Laser exposure problem, image transfer problem. My suggestion would be to ensure you have toner in the cartridge( but by this time it has depleted the developer), and you will need to replace the development unit and possibly the drum Unit. My best guess would be the development Unit.

Munybuny

Ricoh Aficio... | Answered on Sep 05, 2008


HI on the machine there should be a auto reduction enlarge all you need to do is press this place the original on the doc feeder and select the paper cassette in which the paper size you want the copy to be on. Once you have selected press the start button and then the reduction or enlargement is calculated for you.


Hope this helps and answers your question.

Thanks J

Ricoh Aficio... | Answered on Jan 08, 2008


A3 size best is 1 90 to 100 grm

Ricoh Aficio... | Answered on Oct 05, 2007


It depends from machine to machine. on some you just need to enter into service mode and then copy sp or system sp. On other Ricoh machines you need to execute a reset. first of all turn on the machine, and make sure no print jobs are present, or remove the network print or USB print cable and then turn on the machine. This is just to make sure that no print jobs are present, because this will make you to not be able to enter in service mode. This code SC553 also and other similar SC codes like 551,552,544 and etc. are connected with the Fuser unit. Most of the time is just triggered as security for overheat to stop a melting or fire. So if you reset the machine with procedure you may make damage, but in most cases is harmless. But if you reset the SC553 and then after short time reappear than the machine have real problem and need to be fix, do not reset it more than to to times in a row on a short time period. To enter into service mode press the following keys in the following sequence: press the yellow(clear) - then press 1 0 7 (numbers on the keypad) - then press and hold it pressed the red stop button until service mode appear on the screen. when service mode appear on screen enter into (copy sp) or (system sp) depend from the model of the machine. Then with the keypad press 5-8-1-0-# on the screen should appear Fusing SC reset, press execute and after show complete turn off the machine and wait at least 30 seconds, turn it on again. if its ready the sc is clear. But if the sc repeat the machine have a serious problem with the fusing unit and need to be fixed, if you try to reset the machine with this reset to much in short time you may just add more damage. for more detail post the model of the machine.

Ricoh Office... | Answered on Feb 12, 2021


SETTINGS YOU CAN CHANGE WITH USER TOOLS
General Features Panel Key Sound The beeper (key tone) sounds when a key is pressed.
• Default: On Copy Count Display The copy counter can be set to show the number of copies made (count up), or the number of copies yet to be made (count down).
• Default: Up (count up) Function Priority You can specify the mode to be displayed immediately after the operation switch is turned on, or when System Reset mode is turned on.
• Default: Copier Print Priority Set the print priority for each mode.
• Page 20 "Multi-Access"
• Default: Display mode
• When [Interleave] is selected, the current print job will be interrupted after a maximum of five sheets. Display Contrast You can adjust the brightness of the display. Key Repeat You can select whether or not to use the key repeat function.
Measurement Unit You can switch the measurement between "mm" and "inch".
• Default:
• Metric version: mm
• Inch version: inch

Ricoh Office... | Answered on Jan 14, 2021

Not finding what you are looking for?
Office Equipment & Supplies Logo

Popular Tags

21 questions posted

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

Bernard D'Souza

Level 2 Expert

164 Answers

Timothy Van Der...

Level 2 Expert

152 Answers

Cindy Wells

Level 3 Expert

6234 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ricoh Office Equipment & Supplies

  • Ricoh Office Equipment & Supplies

Most Popular Question

sc387 error code ricoh

  • Office Equipment & Supplies
Loading...