20 Most Recent ViewSonic VX922 19" Monitor Flat Panel Questions & Answers


try to remove memory the put it back
Read full answer

ViewSonic VX922... • Answered on Nov 18, 2017


you guys......you don't have a software (driver, refresh rate, etc.) problem. When you first power up the monitor, do you get any display at all (ex, "analog input" or "No input signal")? Of course not - that's because you have a hardware problem with the monitor. Go here and watch the youtube video on how to take apart your monitor and find and replace the "domed" capacitors that have blown:

http://www.tomshardware.com/forum/247964-33-viewsonic-vx922-monitor-black-screen-green-power-light-flashes

Fortunately I only had 1 ($1.76 at Radio Shack). I replaced it in less than 30 minutes and my monitor showed "no input signal" upon powerup as expected because I wasn't connected to my pc which is full of all kinds of drivers and refresh settings, etc.
Read full answer

ViewSonic VX922... • Answered on Oct 04, 2014

Be the first to answer

ViewSonic VX922... • Posted on Aug 31, 2014


Remove the stand. The front bezel separates from the black rear cover. You will need a nylon tool to separate the pieces.
Read full answer

ViewSonic VX922... • Answered on Aug 31, 2014


The part is a capacitor, they go out because of the heat in the monitor. You can check out what they look like at our web site.
www.ccl-la.com/badcaps.htm
If it goes out again, you can fix it yourself.
Buddy
Corporate Computer

Read full answer

ViewSonic VX922... • Answered on May 27, 2014

pdf Manual

VX922 19" Monitor Flat Panel Manual

ViewSonic Computers & Internet | Uploaded on Aug 07, 2013


Hello,This is a very common problem on this series on monitors. The problem is caused by filter capacitors in the power supply board that have failed. You can rebuild the board and the monitor will be as good as new. Here is a link to repair information for the VA1912wb monitors.http://www.ccl-la.com/catalog/product_info.php?products_id=90
Read full answer

ViewSonic VX922... • Answered on Apr 14, 2013


Not a real expensive unit---if caps good you have to be able to check the voltages there next, can you?
Read full answer

ViewSonic VX922... • Answered on Dec 07, 2012

Be the first to answer

ViewSonic VX922... • Posted on Sep 28, 2012


most likely the back light is burned out. Since you do not mention the model number it is hard to tell if this uses a incandescent or florescent bulb.
Read full answer

ViewSonic VX922... • Answered on Aug 01, 2012


Hi,
If you haven't installed some kind of an update manager then these dialogue boxes are most likely due to adware or spyware on your system.
Try installing an anti-spyware utility an do a full system scan for spyware. There are many spyware utilities available on the internet for free. Do a google search to find a free spyware application.
Hope this is helpful.
Regards,
Graemevm
Read full answer

ViewSonic VX922... • Answered on Dec 23, 2011

Be the first to answer

ViewSonic VX922... • Posted on Sep 19, 2011

Be the first to answer

ViewSonic VX922... • Posted on Sep 14, 2011


Since you hadd confirmed that the monitor is faulty with a swap then it seems that the input signal processor is faulty.
Only a signal test will confirm the fault in the stage , so check from the power supply section to see if the set has tripped off due to a protection- if so check the output drivers.
Read full answer

ViewSonic VX922... • Answered on Jul 27, 2011


If the capacitors are polarised electrolytic type then they have a + and - leads. The - lead is marked on the capacitor with a stripe and a - sign. The circuit board where the capacitors are located will be marked with a - sign, make sure the capacitors are located correctly acording to the markings.
You need to put the capacitors with the correct values (capacitor) in the correct place on the circuit board.

If the capacitors are non polarised type the it does not matter which way they are inserted on the circuit board, but they have to be the correct value (capacitor).
Read full answer

ViewSonic VX922... • Answered on Jul 10, 2011

Be the first to answer

ViewSonic VX922... • Posted on Jun 24, 2011


Look for bad caps as shown in my pictures here:
http://s807.photobucket.com/albums/yy352/budm/VIEWSONIC/Viewsonic%20VX922/
Make sure to replace them as a set.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Read full answer

ViewSonic VX922... • Answered on Jun 14, 2011


Look for bad caps with domed top, worst case will be the lamp assembly, see my pictures here:
http://s807.photobucket.com/albums/yy352/budm/VIEWSONIC/Viewsonic%20VX922/

Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed VIEWSONIC monitors to get some ideas what to look for: http://s807.photobucket.com/albums/yy352/budm/ Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Read full answer

ViewSonic VX922... • Answered on May 27, 2011


The monitor shows no signal probably it didnt detect the tower
Ill be advising you to remoev the cable that conencts the cable
used a clean cot or rug clean both ends of the cable , clean also the area whre you plug in the cable , the ports on the monitor and on the CPU make sure its clean .
Then plugged it in , in case nothing happens
try to used another cable that conenct from the monitor to the CPU
you may aslo try to used other CPU to checked if monitor is working fine or try other monitor to checked if the port on the your CPU is working fine
Read full answer

ViewSonic VX922... • Answered on May 23, 2011


Look for bad caps with domed tops.
http://s807.photobucket.com/albums/yy352/budm/VIEWSONIC/Viewsonic%20VX922/

Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/albums/yy352/budm/ Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Read full answer

ViewSonic VX922... • Answered on May 15, 2011

Not finding what you are looking for?
ViewSonic VX922 19" Monitor Flat Panel Logo

138 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

ViewSonic VX2235wm LCD Monitor
ViewSonic VX2235wm LCD Monitor

131 Questions

ViewSonic VX910 19
ViewSonic VX910 19" LCD Monitor

123 Questions

ViewSonic VX2235WM Monitor
ViewSonic VX2235WM Monitor

121 Questions

ViewSonic VX924 19
ViewSonic VX924 19" LCD Monitor

112 Questions

ViewSonic VA720 17
ViewSonic VA720 17" LCD Flat Panel Monitor

104 Questions

Check Out the Mobile Browsers Report
Check Out the Mobile Browsers Report

View all Fixya Reports

Top ViewSonic Computers & Internet Experts

Cindy Wells

Level 3 Expert

6253 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Are you a ViewSonic Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. VX922 19" Monitor Flat Panel Manual

VX922 19" Monitor...

View Most Popular

ViewSonic Computers & Internet

  • ViewSonic Computers & Internet

Most Popular Question

viewsonic va1912wb 3 solid green led but

  • Computers & Internet
Loading...