20 Most Recent Maytag CWE5800A Electric Double Oven - Page 2 Questions & Answers

Yes, replace the lower element by first turning off the circuit breaker to the oven (110V is still to half of the 220V element circuit even though the oven setting is turned off), then unscrew the two screws holding the element to the back wall of the oven, then pull the element out (may have to tug it a bit to get the connectors through the insulation), and pull the wire connector clips off the element.

Hello & Welcome to FixYa

F7 error code is displayed when the clock assembly/electronic range control (ERC) goes bad and needs replacement. Please get back to me if you have any other questions.

Kevin

How many active terminals are there at the main terminal block in the new oven. Is this a single or 2 phase supply. Have you connected the active supply to all active terminals. If only half of the oven is working it sounds like it could be a problem at the terminal block. If so, you need to put a loop or bridge wire to the 2nd active terminal.
If all this was done correctly when connected the only other thing it could be is the electronic clock needs to be set to manual mode for the oven to work correctly.

You need to replace the fan & test the wires for any juice or amps with a electric amp tester.Good luck

Hi and welcome to FixYa. I am Kelly.
Go to this site:
http://www.maytag.com/support/manuals_literature.jsp
Enter your model number CWE5800A
It will ask you what kind of visitor you are... enter that in the drop down menu (Consumer)
There ae 9 manuals for this unit... the alpha letters after 5800 of your model number are what will determine which manual you down load.

The first manual for model CWE5800ACB is here:
http://shared.whirlpoolcorp.com/assets/pdfs/literature/Use%20and%20Care%20Guide%20-%20W10169639.pdf

Self clean steps are on page 9 of the manual. Make sure you read the steps "Before Self-Cleaning" It will tell you to remove the racks and some other important steps.
Thanks for choosing FixYa,
Kelly

Hi - Welcome to FixYa.

Many ovens, including Maytag, have a built in safety feature which prevents opening of the oven door for about 1 hour after the self-cleaning cycle has finished. The self-clean feature works at a much higher temperature than the maximum cooking temperatures so it's designed to prevent access until the oven is fully cooled.

If you have already waited an hour and still can't open it, try leaving it a little longer. If it still doesn't open or you've already been waiting at least an hour, please post back for further assistance.

Hope this helps.

Regards,
BElectric

replaced electric control broiler doesn 't work

When you use self clean the 900 degree temperature damages the electronics. I do not advise using that feature. Get some oven cleaner and do it the old fashioned way. My opinion. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

try turning off power 3 to 5min see if it dosnt reset

Hi,

Here is the body parts diagram of the Maytag CWE5800.So this will help you out in more depth.Please the link to so you can see other parts how it is linked to door too.

Click here to get to the body parts diagram.how to assemble it.

Hope this will help you,


post a comment for further assistance.

Thank you for using fixya have a nice day:-)

Turn off house breaker to the unit at the breaker box of your home. This will be a double breaker.

F7 Touch pad or Control board...... Most techs start with touch pad.

You should first check your breaker Box and Flip both polls off then back on and try it.

If both ovens wont work ((Bake & Broil)) after trying the breaker box then the High limit Thermostat could be the problem, It is located in the rear of the machine.

If this problem happened after you did a self clean, most tech's will start at the High Limit Thermostat.

good day,
hope this link below will solve your problem.

ovens

Here is a web site for most of the parts for your unit:

http://www.appliancepartsworldwide.com/Store_SearchResults.aspx?S=459294&ST=PBM

They also have a phone number, so you may want to call them for additional information for your specific appliance.

As always, if you get stuck, please post another message at FixYa for more help!

Hi. Click here to access your user manual.

the f 2 code is ( oven too hot ) the f 5 ( watchdog circuits disagree / and f7 ( function key shorted or stuck button .. / the clock ( erc ) may have a warped face . ..I would first replace the tempt sensor in oven . if you still have problem repl clock. and problem over .. thank mm ..

Your oven needs to be hard wired to a junction box. No plugs on a oven that pulls 30 or more amps 220v Read your install book that came with the oven.