20 Most Recent Cyberhome DVR 1600 DVD Recorder - Page 2 Questions & Answers

I have an extra 1600 remote.
I Frankensteined 2 dvrs together to make a working unit,
and ended up with an extra remote.

My unit finallt over heated and died, so let me know where to send the remote. You can send me a cd of music or starbucks tiny little gift card for my trouble if you so desire.

[email protected]

What do u mean by formatting?U can't formatted the DVD+RW disc to blank again,after the disc been recorded and used.DVD+RW recodering mean something are recorded u can recorded some elese in it replaced what was there,that all u can do to it.U can't wipe out what in the disc data was there.

Try Amazon.com

http://www.amazon.com/Power-Supply-Cyberhome-CH-DVR1600-Recorder/dp/B004QTBFCI

Yes, this is a common fault and even if he could find a replacement laser it isn't normally costs effective to replace them.

No picture at all even when discs are loaded in the DVD unit? Sounds like an AV switching fault on your TV, not the fact of 'going digital'. The easiest and cheapest way to determine this is to connect the unit to a different TV with AV inputs, to see if there is picture/sound. If so, the unit is OK, and your original TV may have a fault which will require attention by a qualified technician in an authorised service workshop. Unless the TV is a few years old, in which case it would be more economical to replace it with a newer model and/or more user options. If it is not a set with a digital tuner, just analogue, consider upgrading it.

However, if connecting the unit to a different TV produces the same result (no picture etc), then the unit itself is faulty, and again, consider the workshop idea, but if you decide to go this way, get a quote and a second opinion from them first before allowing them to go ahead with repairs.

It could be something really simple.

Only DVD-RW discs can be formatted. If it is a DVD-R and you have already tried recording on it, the disc will be unusable. If the disk is not formatting, it might be defective. Try using another disk in the drive to make sure it isn't your DVD drive itseld that is broken.

Are you using the right type of disk ?
Ie + R / RW or - R / RW
Some machines only take one type.

---

Please dont forget to vote this answer was helpful

Many thanks

------

This is caused by an open (or bad) 10UF capacitor in the power supply. The voltage rating on this cap is too low, consequently, many units suffer the same problem. I replaced my with a 15Volt cap and the unit has been working for over 2 years now.

contact cyberhome to find out who actually makes the unit (e.g. western digital, scientific atlanta). then use the codes for the actual manufacturer on your universal remote. that should do the trick.

U getting the DVR box signal into the tv channel 3?Yes,don't use the tv remote,used the DVR romote as ur remote.

Hi ,

Here are some DIY steps that may help you fixing the problem.

I'm assuming that your unit is dead set without an standby LED light and your outlet is live.1.Power cord - check the cord it might be opened (no continuity).This is due to frequent bending,pulling. 2. Power switch - check for dry joints, open contact. 3.Check the internal fuse- sometimes the fuse fail because of the power surge, replacing with new one will cure the problem, If this is the case I've advice you to use surge protector/AVR (Automatic Voltage Regulator). However if the fuse blew again this is an indication that you have a shorted parts on the power supply, you may visit the link http://www.fixya.com/support/r8053361-fuse_keeps_blowing for more info. If no reaction and still the unit didn't power up then you have an open parts on the power supply.

4.If you see that the fuse is intact on the board, don't attempt to touch anything because there somefatal components stored electricity enough to hurt you with a simple mistake only.

The next steps should be done by an expert or qualified technician because isolating the problem on the power supply is quite technical.

Also check if your unit is under warranty before opening the back panel, it will void the warranty. Avail it because the manufacturer of your unit will fix it for free or a little charge only.

Hope it may help you.

Give a thumbs up if you find it useful.

Thanks for using fixya.

you can find the manuel here http://www.retrevo.com/support/CyberHome-DVR-1600ZU-DVD-Players-manual/id/534ci860/t/2/

Hi we just got one and I was wondering if you ever found a operation manual on line?
Thx

From your description you have a power supply problem, if the remote won't do anything try turning the power on the DVD machine, if that fails the unit will need service or replacement.

Hi.

As other combo models the Magnavox MWC24T5 does not have a video output. The only options offered are audio/video input at the front of TV and audio coax output at the back of TV. There is no video output connector on this TV.

You cannot use this TV to transfer movied from VCR to external DVD RW.

Here manuals:

Magnavox MWC24T5

Cyberhome 1600

Regards.

Ginko.

You could try this? http://www.retrevo.com/support/CyberHome-CH-DVR-1600MU-DVD-Players-manual/id/534ci862/t/2/

Try website like Remotes.com to buy an exact remote to ur original remote.