20 Most Recent GoVideo DV2150 DVD Player/VCR - Page 3 Questions & Answers

If it's not a well known brand, you're likely not going to find a code for it. I've heard of Go Video, but I don't think it's a very popular brand. (I could be wrong on this point)

Codes don't exist for every tv/dvd/vcr/surround system.

If the remote you bought doesn't have your dvd player listed, then you're probably out of luck.

If it's a very expensive universal remote (like $50-$100) then you might find either a code or a firmware update for it on the manufacturers website.

If not, try every code the instructions list. If you're lucky, one of them will work. If not, c'est la vie.

The default password is 3308.
Lola

Hi,
I,m here to rescue you, don,t worry.
Whats the Make-model-number if Any.
Mike @ compurepair.

Just found it at http://www.retrevo.com/s/GoVideo-DV2150-DVD-Players-review-manual/id/1183ag624/t/1-2/  

have you tried using rca cables fro go video to the HD tv?

Same problem here.
Instructions for DV2150 say you can access closed caption toggle by going to SETUP, then OTHER then CAPTION, but this (CAPTION) option is missing from the menu. I, too am struggling with the Jeopardy game buzzers, which I cannot program. Was wondering if the lack of "closed caption" is the reason

You can buy a CD/DVD player cleaner, which is basically a set of brushes attached to a CD. This will gently brush the CD/DVD laser and hopefully that will restore your player to full working order.

i have a dv2130 user guide would the answer be in the guide [email protected]

I had the same problem: I unplugged the power for 10 seconds (literally unplugged it!) and also removed and reconnected the s-video cable. Voila - color picture again!
Good Luck!

clean the heads

when you set the timer you need to ok the settings of the programme you record then you need to switch the video off on the controll as it will only record in standby mode cus if the video is switched on it will wait for you to tell it to record hope this helps

you need to get back into the setting and change the setting that says pal or ntsc this will alter the picture back to what it was check the controll is working cus you should be able to access all menus try doing this without a disk in as sometimes if the disk is in it wont let you into these menus hope this helps

it sounds like your remote has got damp or over time the dust builds up behind the buttons you should be able to take the controll apert and remove the buttons check the pads are clean and not greasy then wipe over the board with some clean cotton cloth where the buttons pads press on to activate usually its just a bit of grease but check their is no button jammed it sounds like this could be the case as you get a different response to pressing the play button so try this first then if dont work still clean the buttons and pads be carefull not to dammage the pads they should come out all together and have little black pads stuck to them make sure their xlean and grease free if this still dont work then you can get but make sure its not one of the cheaper ones a all in one remote this should solve your problem hope this helps

is their a disk inside if their is it sounds like its come out of place and is jamming the door flap either take it to repair shop or if you feel ok taking the casing off have a look if anything is jamming it it migh just be a spring on the flap has come off try opening the flap with your hands but be gentle doing this as not to damage it it may just be its got knocked and a disk has jumped out of place so try having a look inside to see if it is jammed but be carefull not to damage anything taking the casing off make sure it has been off for 24 hours before you take the case off as they can still have electric stored inside for this time but if you are unsure what you are doing let a pro do it they wont charge much as it is easy to solve prob hope this helps you

From http://kbase.x10.com/wiki/Universal_Remote_Code_List

try either code 359, 368 or 375


Mike

Here is an easy trick to see if a remote is working. Hold the remote up to a digital camera or camcorder. Then just press the buttons on the remote and look in the lcd screen of the camera. If the remote is working you will see the LED on the front of the remote flashing through the LCD screen of the camera. If you do see it blinking on the camera then you know it works. If it works then you either have the wrong remote for that model, or the reciever inside the dvd player may be faulty. You can also pick up a universal remote for under $10 at most stores that sells electronics. Peter

Progressive scan is turned ON...find it in your menu and turn OFF....GJ

you could also check that the regioncount hasn't been exceeded it can only be changed a certain number of times

It may have condensation inside. Leave it plugged in for 24 hours and try again. There is a sensor on the VHS head.

Govideo DVR4300 Manuals ' ManualsLib

https://www.manualslib.com > ... > DVD VCR Combo Manuals and User Guides for GoVideo DVR4300. We have 2 GoVideo DVR4300 manuals available for free PDF download: User Manual, Specifications · 1 Getting Started. ..

Clean w solvent or unplug n letit reboot for awhile. It may b a tech issue. Kimkomando.com for digital problems