LG WM2688H Front Load Washer - Answered Questions & Fixed issues

AK Techno Service is one of the best http://aktechnoservice.com/lg-washing-machine-service-center-in-hyderabad/ . Front load top load semi-automatic drum failure, PCB repair service etc.
Here,you can find any type of solutions for your LG Washing Machine.


LG WM2688H Front... | Answered on Sep 03, 2018 | 711 views

You need a new drum. Those holes are caused by the sharp edges of the baffles which cause the clothes to tumble.

If you can find the sharp edge you could put epoxy putty on it. However if it is 12 months old, it should be a warranty issue as you have only just found out what is causing it.

See the link
LG washing machine support number Google Search

LG WM2688H Front... | Answered on Mar 01, 2018 | 122 views

hi nynaults.
not sure if this link will help you find out but have a look.
how much Water level in LG 2688 Google Search

LG WM2688H Front... | Answered on Nov 03, 2017 | 111 views

TE is a Therrmistor error, The thermistor senses the water temp. As with any error code it could be the part, Wiring Harness or Computer which is causing the issue. If you try cold temp wash the cycles may work. Geeks should OHM out the part to see if that is at fault. LG has 2 different Thermistors. 1. Thermistor is part of the heat element.
2. Thermister is separate. LG part# 6322FR2046C.
Quick easy fix.

Hope this helps.

LG WM2688H Front... | Answered on Oct 31, 2017 | 71 views

Are you sure it is not an "tE" error code. Sounds like a thermistor error. A $6 part. Kinda easy to replace but must turn washer on its back or side to get to. Answer back with a comment to this answer if you want more info or repair guidance.

LG WM2688H Front... | Answered on Mar 31, 2017 | 85 views

Thanks to a couple of previous responders, 6 months of frustration has now ended - I can now run the Tub Clean on my LG Steam Washer! I first want to say that it is important not to get excited and start pushing buttons randomly, as I think I had been doing for all these months when I couldn't get Tub Clean to work by pushing the button in for 3 seconds. Just do the following, which combines and expands on a couple of previous responses:

1. I had to deactivate the Spin Sense, and if your Spin Sense is ON, you will have to do this too. (It is ON if the spin speed light flashes while any of the wash cycles is in progress. If spin speed button does not flash while a wash cycle is in progress, the Spin Sense is already off.) So how to deactivate Spin Sense? Select Speed Wash, and start the cycle. Let it run for about 20 seconds and THEN push and HOLD IN in the Spin Sense option button for 3 seconds. The blinking spin speed button will stop blinking and you will then know that the Spin Sense is OFF.

2. Once Spin Sense is off: Start with your machine turned off. Then push the power button on and select the RINSE AND SPIN option button. Then START the Rinse and Spin cycle. Let it run for about 5 seconds and then PUSH IN AND HOLD THE TUB CLEAN OPTION BUTTON FOR 3 SECONDS. You will then see the little LED light panel show something that looks like tcl. And you are there! Just leave it alone .... the LED will change to one hour and 25 minutes. And it will clean your machine just great.

3. Don't forget to put your bleach in the detergent cup before you start all of this.

I want to thank the two responders above who gave me the essential features for this fix. I forgot to make a note of their names before I started this response, but you can see who they are. I am so excited. Now EVERYTHING works on my LG Steam Washing Machine. I love this machine. It is a miracle of cleaning, especially since I own 4 large breed dogs and am washing and sanitizing large hairy and smelly bedding each and every day. And I no longer have to iron anything - I just use the steam cycle to unwrinkle our clothes. Best washer I have ever owned (and I have owned another major brand of large capacity front loading washer before - no comparison).

LG WM2688H Front... | Answered on Oct 11, 2017 | 8,996 views

Model# not coming up WM2688H need Right number.
you say your getting a PF code
sound like loose connection somewhere.
getting a glitch in the power at power up Need more details on what first symptoms were B4 any parts changed and list of parts changed
will PF cancel on controls takes a few seconds then flashes PF?
Send us a bit more on symptoms from first plugging in washer what it dose.We then can give you more detailed answers
Thanks . for posting

LG WM2688H Front... | Answered on Aug 02, 2015 | 58 views

No button, but LG customer service says unplugging the unit for 1 hour and then holding the power button while turning it on will reset the computer.

In my experience this does work, but I don't think it resets absolutely everything.

Another time I had a problem LG customer service told me to unplug the unit, hold the power button for 60 seconds and then plug it back in. I can't confirm if this works or not, but it is worth a try first (60 seconds is a lot shorter than 60 minutes...).

LG WM2688H Front... | Answered on Jul 22, 2015 | 6,578 views

For LG washers, the DE error indicates a problem with the door lock. If you just started the cycle and the error occurred, then the door couldn't lock properly. (The machine turns off and indicates the error so that the water won't flood your laundry area.) First check if there are any clothes between the door and the frame. If needed unplug the washer for 5 minutes. Then restart the machine try to open the door. If you pressed Pause, wait a minute or two. If the error occurs at the end of the cycle, it may not be unlocking properly.

The latch mechanism may have failed or the PTC sensor in the latch has failed. The entire latch would need to be replaced. Here's one: http://www.appliancepartspros.com/lg-door-lock-switch-6601er1004c-ap4441836.html . If the door locked failed with the door closed or the washer is under warranty, contact LG or a repair professional for service.

I hope this helps.

Cindy Wells

LG WM2688H Front... | Answered on May 18, 2015 | 114 views

my washer also was leaking from the dispenser and I had a cap from one of the detergent bottles stuck in the inlet hose. Don't know how it got in there but glad I found it so if your washer leaks from the soap tray it could be a cap from your detergent bottle stuck in there.

LG WM2688H Front... | Answered on Jul 15, 2014 | 1,208 views

if it fails to stop running only at the rinse part of the cycle it is probably in the timer as the solenoid valve has to cut the water off when the washer fills for the wash cycle too. fills for wash cycle and cuts off water, washes and drains, refills for rinse cycle and water just keeps running? does this every time you run it? that's in the timer. bad solenoid (water inlet valve) would keep running even on wash fill up. hope this helps.

LG WM2688H Front... | Answered on May 16, 2014 | 397 views

The switch assembly on the door may be defective, check for continuity and replace if necessary.

LG WM2688H Front... | Answered on Mar 28, 2014 | 24 views

There should be a spring clamp of some kind,use a pair of pliers to squeeze the clamp open and slide it off the hose.

LG WM2688H Front... | Answered on Apr 23, 2012 | 307 views

repairclinic.com is your best bet

LG WM2688H Front... | Answered on Apr 15, 2012 | 51 views


Please check this diagram:


and if you require click on this link to download the service manual for your LG WM2688H Washer. Hope this helps...please post back for further assistance.


LG WM2688H Front... | Answered on Sep 22, 2011 | 19 views

You may have a broken motor sensor and it will need to be replaced. You will need to call a qualified service technician who can work on LG's to help you with that.
Good luck

LG WM2688H Front... | Answered on Jun 15, 2011 | 35 views

Hi from retired Englishman in SW France,
'te' for an LG normally means 'heating error' (Temperature).
(It might be worthwhile trying this but sorry, no promises 1)
This could be that the element is coated in calcium. I suggest you run the contents of a couple of sachets of proprietary limescale removing powder/fluid through it. The most efficient way is to put the contents in an empty washer and pour a kettle or two of boiling water into the drum then leave overnight. In the morning run just a spin; the water mix will then go through the drain filter and drain motor impeller blades, doing absolutely NO harm whatsoever, in fact some good!
You could also consider repeating the action ;-0)

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

LG WM2688H Front... | Answered on May 27, 2011 | 375 views

You may have a "slow drain" condition caused by a weak water pump.

Fixya link:

LG WM2688H Front... | Answered on May 02, 2011 | 260 views

I am sorry to tell you thaqt the control board has shorted out, and will need replacing. DO NOT TRY TO OPERATE THE WASHER ANY FURTHER. IT COULD CAUSE A FIRE ! ! !

There are many online parts sellers, who will help you get the right part.

LG WM2688H Front... | Answered on Mar 27, 2011 | 94 views

Not finding what you are looking for?
LG WM2688H Front Load Washer Logo

150 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

85222 Answers


Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides