20 Most Recent LG WM2277H Front Load Washer - Page 3 Questions & Answers

If there is no obvious provision for changing over from left to right or vice-versa then you are stuck with the one direction. You have to remember that the door operates the overall control master switch and therefore there would also have to be facility to relocate the switch and tab if you were to achieve what you are thinking about.Next time, buy a machine the door of which opens and closes in your most preferred direction.....that's all there is as an alternative. Poppa http://www.cdbaby.com/cd/poppamadison

When you see a fault code, always think that this may be just the indicator that other faults may be developing.That is why it is so important to call out a qualified Technician to check your machine completely. He/she can see what else is starting to show signs of wear or failure or even things that have come loose and need tightening up.It is worth paying for a Service Call for peace of mind and finding out where your machine is really at in its life cycle. Poppa http://www.cdbaby.com/cd/poppamadison

Pack it in the same way that it arrived when you bought it. You can always go back to the store where they sell it and get some further advice. Poppa http://www.cdbaby.com/cd/poppamadison

It's a bit late, as I guess you have moved by now!The best way to drain fully is to remove the outlet hose and let the machine lean backwards against an outside wall so that all water drains out. Poppa http://www.cdbaby.com/cd/poppamadison

Any water leak presents the danger of ELECTROCUTION with machines operating at mains voltage.Never, but never use a leaking machine until the problem is fully remedied. Call a qualified Technician and get peace of mind for but a few dollars. Poppa http://www.cdbaby.com/cd/poppamadison

An EEprom is an electrically eraseable programmable read only memory. It stores the programme that tells your machine what to do and in what sequence.

Being an integrated circuit electronic component, like any other, they can become faulty or their connections can become tarnished or corroded which causes contact problems. Often it is only a matter of removing the EEprom and cleaning it and the socket with WD40 or a similar contact cleaning fluid. At other times it may mean that the component must be replaced and by one with an updated software version of the control programme. Poppahttp://www.cdbaby.com/cd/poppamadison

Run a "Washing Machine Cleaner solution" through your machine to clean out built up grime and dirt inside the drum.You must of course always only load up clothes so that there is good space left for them to move freely. Jammed up clothing will never wash clean.Use a really good detergent, and my tip is NOT to use fabric softeners as they really gum up the works and cause grime and dirt buildup in places you cannot see! This mucky stuff then finds it way back into the next wash and the next and so on. Poppa http://www.cdbaby.com/cd/poppamadison

Le solution!Call out a qualified Service Technician. This may not be the only problem with your machine. An experienced Tech can spot impending failure of other items while doing an inspection and giving you a quote for repair, just for the cost of a Service Call. Poppa http://www.cdbaby.com/cd/poppamadison

Possibly a fault in drive motor control circuit board. Poppa http://www.cdbaby.com/cd/poppamadison

If you mean that water does not come into the machine at all then you need to have the water inlet valves checked by a qualified Technician for correct operation. Poppa http://www.cdbaby.com/cd/poppamadison

Either an item of clothing is jammed between inner and outer drum or the bearings are faulty.Job for qualified Technician involving machine dis-assembly to remedy. Poppa http://www.cdbaby.com/cd/poppamadison

Because there is a fault condition with your machine. It may have other faults developing slowly which only a qualified Technician can advise you about.Get peace of mind and stay safe...Pay for a Service Call. Poppa http://www.cdbaby.com/cd/poppamadison

DO NOT USE ! REPEAT.....DO NOT USE !Turn off machine ! Disconnect from Power! This machine is a danger to life and limb......You and that of your household or family.Get it immediately checked by a qualified Technician and fixed properly or buy a new machine.Trust me ! Poppa http://www.cdbaby.com/cd/poppamadison

Does your User Manual say anything about this being likely to happen?Sounds as if there is a throw-up of water into this hosing in the spin cycle or some such thing?Do check your water hoses are tightly screwed. I have seen cases where fine jets of water spray into odd places which cannot be seen when the machine is backed to the wall. Poppa http://www.cdbaby.com/cd/poppamadison

You will readily find this out by booking a Service Call to have the manufacturers authorised agent take a look at your machine.You see, this may not be the only problem with your machine. Get the benefit of knowing eyes and minds to give you real peace of mind with a full check up for the cost of a call out. Poppa http://www.cdbaby.com/cd/poppamadison

You will most likely need to call an authorized service agent in order to find this out. That likely means paying for a service call.But heck........if you want an answer.......go for it! It may just be a simple fix! Poppa http://www.cdbaby.com/cd/poppamadison

Could be the water pressure switch is faulty and/or the electronics control circuitry.Suggest you called a qualified Technician to fix it. It will be worth it for many reasons. Poppa http://www.cdbaby.com/cd/poppamadison

Disconnect machine from Power.Spray some WD40 or similar product over the hinges while you work the door into the closed and open position, until it all loosens up.If this does not work then the hinges must be so badly corroded inside that they will need replacing. Poppa http://www.cdbaby.com/cd/poppamadison

If your machine offers that facility and it does not work when you select it, you need the services of a qualified Technician to check out the control electronics. Poppa http://www.cdbaby.com/cd/poppamadison

Unless you are a person qualified in such matters. No one who cares about your safety is going to suggest that you should attempt this. It is not just about removing and replacing something, it is about the possible dangers caused to oneself through inexperience and ignorance of electrical safety procedures.A service call to a qualified Technician will repay you with a good result and peace of mind in all respects. Poppa http://www.cdbaby.com/cd/poppamadison