20 Most Recent Konica Minolta DiALTA CF910 Copier - Page 2 Questions & Answers

Hi,
Please download your driver here : http://ptf.com/vivitar/vivitar+vivicam+55+driver/index3.html

The problem is in the fun motor section.Verify the exhaust fun mototr and the transfer fun motor.

Your TCR sensor is dirty. Your need to take out your process unit( drum unit) and vavuum waste toner out of the hopper, and clean the TCR sensor. this will fix your problem. first remove the developer unit one screw, than the drum unit one screw. place the drum unit on the copier w/the drum facing up. remove charge wire asy, drum shaft, and bearing, than the drum, remove the cleaning blade asy. you'll see the excess toner, vacuum all out. clean the tcr sensor, locate in the middle lower part of unit, under the drum. this should fix your problem.. lots of work though... good luck

Sir CF910 is a legacy equipment, try going to konicaminolta US web site look up you machine and down load the driver for it if a available once again CF910 is a first gen color machine from minolta, Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

slide the drum unit out and see if the line on the drum. check your fuser roller for any scrach.

when i moved this unit fluid came out like oil is this a major problem

Try turning off the machine, pushing and holding the utility key and turning it on, don't take your finger off the key. You should see a blank screen with one touch button on it saying Trouble Reset. Press it, if the machine doesn't reset itself turn it off and one again.

Corona wires are used in the transfer/sep assy and drum charge. C0200 is code if they fault. To reset the machine open and close the front door, if ithe code comes back the corona wires and or assy need replacement Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

you probably need you fuser rebuilt. the heat roller melts the toner into the papew. it is covered in teflon. over time the teflon wears off anf toner sticks to it causing paper jams when the copier gets hot

Manual by pass paper lifting failure.Check the manual paper feed pick up solenoid and the tray lift up sensor.Verify the paper misfeds and power supply unit.

Enter in the service mode :stop 0 stop 001 and select in the tech rep mode the touch panel adjustment.

Enter in the service mode Stop-0-stop-0 -0 -1 and select in the tech.rep.mode the touch panel adjusment.

The sensor for the door mayhave dust on it, also the mirco switch which is activated by the door may be pushed into far due to the door being closed to hard:(. As for the sensor use some can air. lastly the door actuator mounted on the door mite be broken off the door. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Have you checked that the paper matches the operator panel and the paper draw, landscape vise portrit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You reset the code by pressing the "Trouble reset switch on the Tech Rep setting Switch board, located under the control panel, open the machine front cover its a small circuit board with two small black press type switches (left side switch) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

stapler issue, open close finisher door. second, check the stapler cart. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

CF910 is Minolta first generation color copier, does any color like green or blue color have the same problem, there will not be any error message to change image units. only toner. The machine has only one drum, and each color gets a chance to place its color on the drum. Paper is held by the big plastic drum next to the drum. You should think about having a service technician come out and look at it. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f