Konica Minolta bizhub 180 All-In-One Printer - Answered Questions & Fixed issues

Press Utility / Counter -> {STOP}{0}{0}{STOP}{0}{1}, now you should be in Service Mode. Go to Service Choice - > IU LIFE STOP MODE -> and choose CONTINUOUS.

where does it jam the screen will display where the paper is jammimg Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

did you replace the developer also did you clear the counters first did you run the F8 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Main motor is jammed or bad Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Check the accurator for the sensor that tell the copier paper is there might be broken or out of alignment Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Service manuals electronic components datasheets and equipment schematics... try this site Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Service manuals electronic components datasheets and equipment schematics... try this Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the drum and the developer Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Sir/Mam Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work, you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

paper size error check the draw guides the docfeeder guides and proper media system metric or inch Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

try this site Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

use your zoom feature most copiers don't have a conversion metric a4 to inch (US) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

loose USB cable usually the problem in bizhub180, check / reinsert .

where is the jam located??????????????? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Any electrical problems might have a bad board or memory issue Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Went thru the Bizhub 180 service manual and operators manual no H14. What model machine do you have Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Utility stop 0 0 stop 0 1 allows U to sevice mode. Go to clear data and clear supply count. M2 will be cleared.

The error code is a main motor has probably failed you will need a technician to diagnose and replace.

fuser module problem...has to be removed and troubleshoot... problem will be fixed.....

sintam se cumprimentados, estou com um problema na minha bizhub 211 ela pede para contactar tecnico (M1).como faco