Top 20 Konica Minolta bizhub 350 All-In-One Laser Printer Questions & Answers

Change the marketing area from EU to US in Service mode.

When you installed the driver did you check the boxes for the installed options? Plus you may have to check the box for saddle unit. Hope this helps.

What printer is it ? Some older ones need manual calibration, where patterns are printed, then you tell the system which is the best one. Newer ones can self calibrate, but still need it done. Go into your printers menu and see if you can find something on calibration or allignment.

have tech come out and flash the firmware on the machine THE COPIER OS Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

This website will perhaps not be the place to check prices. Try Staples; Amazon, ebay etc. By the way we cannot know which country or city your school too search for your model in ebay. a used one appears below Konica Minolta Bizhub C350 Color Copier Printer Scanner FREE SHIPPING in...

check the draw guides Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what is the sp mode????? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Check the UN2 connector for proper connection and correct as necessary. - - 2 Remove the Developing Unit from the IU, and then replace UN2. - - 3 Run F8. - - 4 Change PWB-A - - 5 Change PU1

http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=Konica-Minolta&model=bizhub%20C350

Could try and help you fix it if I knew what the fault was. Give me a full description plus fault code.

Is there any info on the control panel before it restarts? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

A few things could be wrong.
1. Check if the toner is not bad, all hard as a rock. If so replace it
2. Check to see if the toner bottle isn't dammaged. If so replace it.
3. The toner auger is clogged? Vacuum the whole toner hopper out so it empty then add a fresh new toner. If it adds toner you will know. If it doesn't then the ring the toner bottle sits in is siezed. Remove it and clean throughly.
3. If all that seems good your going to hafta get a new hopper unit.

if you have a C2557 after changing F8 developer then your extra toner is too strong. Check your clutch adding toner, replace the small foam with an equivalent thickness, increase your toner and repeat a gain F8.

Does it say ABORT then a code? need the full code include all zero and x Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

do any other document word, etc. print? Try this site for most up to date drivers Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Shutter unit defection.Press Utility key-Meter count-Check details-00000000-End and you entering in service mode,select trouble reset.The very simple method is remove the finisher/exit unit and work without.

This is simple. There are a bunch of sensors in the adf that read the paper size. Your adf is telling the copier that your copying 8.5x5.5 that's when the copier blanks out the rest of your page. So do u have any scrap of paper or sensor that is blocked they have spring loaded flags on them sometimes the spring will fall off and cause this so look very carefully and you will find the little sensor that is causing your problem. Also there are photo sencors that get dusty. So use canned air to clean them out but be careful you could knock off the springs on the flags with air.

Turn OFF the machine and then ON.

C5351 Power Supply Cooling Fan Motor Failure The Power Supply Cooling Fan Motor Lock signal remains set to H for a set period of time while the Power Supply Cooling Fan Motor is turning. • The Power Supply Cooling Fan Motor Lock signal remains set to L for a set period of time while the Power Supply Cooling Fan Motor remains stopped.