Top 20 Konica Minolta bizhub C351 All-In-One Laser Printer Questions & Answers

explain column????? send a pic???? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

control is dead or the image control board have a tech come out to check it out. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

That is because your registration is off which mean the magenta/cyan are not laying on top of each other so you get (blur) a purple, Stabilization has nothing to do with that you need to have registration procedure run, that mean printing out a certain print out and checking the the print out to determine which way to compensate the LED 's. Just me but I would call a Technician in the morning to come out, and run the test, it not simple once you see him run it you will see why. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Low power code fuser not warm up properly

Mr. Gates, yes there is away to change the pw recommended you get a tech out to do it. Change admin pw not over the internet. Should have a paper work to back it up. Big time security thing Hard drive access and stuff Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Might require having the firmware up graded get a konicaminolta tech out to up grade the firm ware from a secure konicaminolta web site. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

C0206 Tray 3 feeder up/down abnormality • The tray 3 upper limit sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.

Does your office use a PBX system where you have to dial a 9 before gaining access to outside line. Are you using one touch buttons do they have the 9 included. Is the machine connected to a analog phone line not a digital line has to old POT line not a digital. Using a two line phone line? take the line from the wall look at the connector do you see four wires or two at the connector green, yellow, black and red. If so get only a two wire cable. Do you have EMI collar on the phone line? Check the line with a old "Princess Phone" from radio shack.. Move the copier to a different wall outlet. Have a tech check the fax connections and setting on the copier. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Thermisters / Heat Sensors abnormality. Replace the thermisters, in order to get rid of this problem permanently.

does it have the fax option ? if so try this web site for the manual Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Replace the fusing unit Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Only touch screen can be replaed.

Well you have to get that option kit from a Konica Minolta dealership if they still have them. Sure the duplexer is installed just not plugged in would be attached to the right side door. will require two or three screws and a connector or two. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

find a dealership for Konica minolta Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Check your default on computers, via control panel might be set to default to by pass tray. Also check the paper selection on the copier ensure not defaulted to by pass tray Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

DO you mean C550 Copier/Printer? P-14 means problems with the following 1. PH relay board (REYB/PH) 2. Printer control board (PRCB) 3. PH unit 4. Imaging unit Recommend you get a tech out to look at this problems Print head (PH) contains the LASER. Printer Control Board $$$$$$$$$$$$$$$. PH/ REYB?PH board ALSO $$$$$$$$$. Again have tech come out look at this machine. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

what where you doing when this happen Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

remove the box from the finisher Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

You do not turn on the Print Driver. the print driver is on your computer which allows the computer to talk to the printer. when you click print on the computer your C351 should be the printer it goes to. try this site for help Self Help Product Support Konica Minolta Business Solutions Inc Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

does it copy??? try different file different program pdf, web page does it print the demo page does it print the counter page???? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f