20 Most Recent OKI MICROLINE 280 Elite Matrix Printer Questions & Answers

0helpful

1answer

OKI ML 280 Elite

You have the Printer emulation set incorrectly. I think it comes as IBM as default and you should try Epson instead. Its a trial and error thing but am sure emulation is incorrect.

Read full answer

7/2/2017 8:31:24 PM • OKI MICROLINE... • Answered on Jul 02, 2017

0answers

Alarm 280 elite

Read full answer

Be the first to answer 10/15/2013 12:24:04 PM • OKI MICROLINE... • Posted on Oct 15, 2013 • Be the first to answer

0answers

What should the Dip switches be set to when using

Read full answer

Be the first to answer 8/22/2013 3:16:58 AM • OKI MICROLINE... • Posted on Aug 22, 2013 • Be the first to answer

0answers

OKI mocroline 280 elite 9 pin printer prints blank

Read full answer

Be the first to answer 8/3/2013 4:32:15 AM • OKI MICROLINE... • Posted on Aug 03, 2013 • Be the first to answer

0helpful

1answer

The printer Microline 280 elite

I have a link below that can help you with regards the dip switches.

Just click HERE so that you can get to the site

Click HERE as well because this is the description for dip switches

Click HERE because this is the diagram and more explanation of dip switches.

I hope that all the links I gave you can help you resolving the issue.

Thanks.

Read full answer

8/5/2011 10:59:21 AM • OKI MICROLINE... • Answered on Aug 05, 2011

0answers

OKI ML 280 Elite gives

Read full answer

Be the first to answer 1/31/2011 12:26:48 PM • OKI MICROLINE... • Posted on Jan 31, 2011 • Be the first to answer

0answers

Oki microline 280 Elite jumper

Read full answer

Be the first to answer 12/1/2010 2:30:33 PM • OKI MICROLINE... • Posted on Dec 01, 2010 • Be the first to answer

0helpful

1answer

Microline 280 dose not roll

If you have replaced the stepper motor and it has not changed anything then it is obvious that the stepper motor may have been OK. It is the electronics that is at fault. The module that controls the stepper is at fault. It needs chip level repair which only a qualified technician can do.Please visit the customer care of OKI for the needful.

Read full answer

11/27/2010 1:38:23 PM • OKI MICROLINE... • Answered on Nov 27, 2010

0answers

OKI ML 280 Elite gives alarm. It was printing but

Read full answer

Be the first to answer 10/27/2010 9:41:34 AM • OKI MICROLINE... • Posted on Oct 27, 2010 • Be the first to answer

0helpful

2answers

RE: I am always looking for HP / COMPAQ obsoleted printers...

Hi Mr. RICHARD VARGAs,

please follow the link below,here you can see many series of printers

http://h20180.www2.hp.com/apps/Lookup?lang=en&h_client=S-A-R163-1&cc=us&h_query=all+printers&h_page=hpcom,igmx&h_pagetype=s-001&h_cc=us&h_lang=en

thanks
ttyagi

Read full answer

8/11/2010 5:27:36 PM • OKI MICROLINE... • Answered on Aug 11, 2010

0answers

OKI MICROLINE 280 Alarm light wont go off

Read full answer

Be the first to answer 10/12/2009 2:38:30 PM • OKI MICROLINE... • Posted on Oct 12, 2009 • Be the first to answer

0answers

Oki 280 will not feed paper

Read full answer

Be the first to answer 9/28/2009 6:05:02 PM • OKI MICROLINE... • Posted on Sep 28, 2009 • Be the first to answer

0answers

How do you set up the OKI Microline 280 to print from RS-232?

Read full answer

Be the first to answer 7/13/2009 3:30:33 PM • OKI MICROLINE... • Posted on Jul 13, 2009 • Be the first to answer

0helpful

1answer

EVERY TIME PRINT GET A EXTRA SHEET BLANK PAPER

Printer setup defines different emulator you can use such as IBM Pro/ Brother/Generic. Try a different one that as set now. See if that helps. Does it do the same of printing with a different
application? You may have page length setup wrong in application.

Read full answer

9/26/2008 4:05:16 PM • OKI MICROLINE... • Answered on Sep 26, 2008

0helpful

1answer

Oki microline 280 feeds paper continiously after a file print, and won't stop till i pull power cable

First, reinstall the driver and be sure it's the correct driver for this printer. If you drive a word document does it do the same? If not, chanses are the db application is constantly sending form feeds to the printer and the printer will do whatever it's told to do. Try a different printer setup in the db application.

Read full answer

9/26/2008 4:01:11 PM • OKI MICROLINE... • Answered on Sep 26, 2008

0helpful

1answer

OKI MICROLINE 280 Elite Matrix... Problem

Be sure when you install new paper that the paper out switch, usually in the paperpath somewhere, is being contacted by the new paper. Usually located on the left side of the paper platten.

Read full answer

9/26/2008 3:56:06 PM • OKI MICROLINE... • Answered on Sep 26, 2008

0helpful

1answer

Oki microline 280

Check printer setup where you define carrige return and line feed options. Alot of times you need to set printer to do an auto CR on reciept of LF or auto LF on reciept of CR. I run into this all the time.

Read full answer

9/26/2008 3:50:00 PM • OKI MICROLINE... • Answered on Sep 26, 2008

0helpful

1answer

Form feed length for 280

change in your computer driver setting
if you using windows xp
click to
start
settings
control panel
printer and fax
select your printer and right click
properties
in general menu
printing preferances
change here paper size
select letter 8.5" 11"

Read full answer

2/29/2008 10:36:21 AM • OKI MICROLINE... • Answered on Feb 29, 2008

0answers