Polaroid FLM-2632 Television - Page 5 - Answered Questions & Fixed issues
No Sound
1) First check the mute.
2) Make sure there aren’t headphones plugged in, that will disable the speakers.
3) Check the audio setup
4) Check your Volume lock
Changing Volume Lock
The remote comes preset to allow independent volume control of each selected device (Global Volume Unlock).
However, you may change the Volume Lock setting to Global Volume Lock so that one device’s volume will
control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected device to
set its volume control for independent operation or Global Volume Unlock to remove all volume locking.
Locking Volume Control to One Mode (Global Volume Lock)
1. Press and hold SET until the red LED blinks twice; then release.
2. Enter 9-9-3 and then press the mode key for the device you want to control volume (for example, TV).
The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example,
TV) will control the volume regardless of the current mode.
Unlocking All Volume Control (Restoring Global Unlock)
1. Press and hold SET until the red LED blinks twice; then release.
2. Enter 9-9-3 and then press VOL+. The LED blinks four times. Volume is now
independently controlled for all programmed devices.
Unlocking a Single Device’s Volume Control
1. Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX).
2. Press and hold SET until the red LED blinks twice; then release.
3. Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is now
independently controlled for the selected
4/24/2009 7:42:54 PM •
Polaroid...
•
Answered
on Apr 24, 2009
•
2,567 views
FLM 2632 WILL NOT POWER ON
Problem here is the wont sell just the power supply, it comes with what is called the control box assembly. Part # 909-KS0-GF271XAH On factory bakorder and no ETA and for $ 431.85 at
www.vancebaldwin.com
6/8/2008 3:35:57 PM •
Polaroid...
•
Answered
on Jun 08, 2008
•
236 views
Polaroid FLM-3228
cheak cables gold leads only hi end ground antenna good power strips get any magnets stuff away from it interfence ok
2/12/2008 1:11:29 AM •
Polaroid...
•
Answered
on Feb 12, 2008
•
122 views
Buzz from back of the tv
It is likely that one of the transfomers is buzzing due to heat and laminations or wire is ringing.
It should not cause any issue except annoy you. it must be replaced. or
glued back down which is usually very difficult as they are wrapped
and/or sealed.
Only way to find out is to open the unit and trace it down.
If it is dust buildup then you should be hearing a crackling. zzzztt sound.
1/31/2008 6:52:00 PM •
Polaroid...
•
Answered
on Jan 31, 2008
•
94 views
Picture is not stable
Check the Power Supply board to see any puffed capacitors. If found faulty cap, replace them.
1/5/2008 2:08:42 PM •
Polaroid...
•
Answered
on Jan 05, 2008
•
166 views
Nosignal
you need an outdoor antennae or a cable conection. Mke shure that your connecting cables are in good condition. also check the ("F" fitting, that is the end of the cable that screws on to the back of the tv, sometimes the center wire gets bent and it dosen go into the center conection.
Lou Margo
Allied Electronics
[email protected]
12/7/2007 10:03:08 PM •
Polaroid...
•
Answered
on Dec 07, 2007
•
73 views
No sound
Are you using a set of sound wires in addition to the HDMI cable? - HDMI only carries the HD Video and no audio, so you still need either a digital or audio cable to pass the audio to the set.
1/4/2009 7:21:09 PM •
Polaroid...
•
Answered
on Jan 04, 2009
•
177 views
Polaroid FLU-2632
I had the same problem. It's caused by the picture setting on your Sky box. Go ibto Services, select Picture Settings and set the mode to PAL not RGB.
12/31/2009 4:22:52 PM •
Polaroid...
•
Answered
on Dec 31, 2009
•
1,037 views
Ratio
Does the sky box have a setting for output ratio?
If so try adjusting it and see what the TV does.
6/10/2007 1:05:31 PM •
Polaroid...
•
Answered
on Jun 10, 2007
•
135 views
No Power
I have the same TV and it did the same thing. I called Polaroid's customer support line and they were very helpful. They sent in a work order to the local servicer in my area. I then got the number of the place (VIEW ELECTRONICS) and called them a few days later. They said that it was a very common problem and that they knew exactly what part it needed and ordered it. At the moment, i am waiting for the part to arrive and when it does i can just take it into the store and it will take them about 20 minutes to install and that should be it. I'm not sure what caused it but hopefully this part will fix it. Hope this helped...
5/23/2009 12:09:00 AM •
Polaroid...
•
Answered
on May 23, 2009
•
189 views
VGA input
is your laptop capable of sending widescreen video to your TV or can it only send 4:3 video?
5/26/2007 6:24:49 PM •
Polaroid...
•
Answered
on May 26, 2007
•
142 views
Remote
The manual for this TV can be found on this page: http://www.polaroid.com/service/userguides/ce/ce_ug.html
The specific pdf for the FLM 2632 is here:
http://www.polaroid.com/service/userguides/ce/lcd_tvs/flm_series_ug.pdf
5/11/2007 5:24:21 PM •
Polaroid...
•
Answered
on May 11, 2007
•
112 views
Problem with my flat screen polaroid
Check all your connections if they are connected properly.if connections are good that means the tv is having problems in the color circuit call a tech to do repairs on your tv.good luck.
4/14/2007 2:07:20 AM •
Polaroid...
•
Answered
on Apr 14, 2007
•
158 views
Bad Cable Input
Try using your RCA imput to see how the picture looks compared to the tuner picture,is possible your tuner imput is bad,make sure the conector is not loose,the overall picture should look different but not fuzzy all over,using a dvd picture thru the aux (rca)imput should show you the difference.If the conector is loose only it could be repaired but if it is solid the tuner might be bad and it will need to be replaced along with any board it might be mounted to.Let us know how it goes or if you need more information.
5/22/2009 3:30:56 AM •
Polaroid...
•
Answered
on May 22, 2009
•
264 views
Polaroid TV working with constant red flashing light
If your Polaroid Roku TV is working fine but the red light is continuously flashing, it could indicate an issue that may need attention. Here are some steps you can try to troubleshoot the problem:
- Power Cycle:
- Turn off the TV and unplug it from the power source.
- Wait for at least 5 minutes.
- Plug the TV back in and turn it on.
- Check Remote Control:
- Ensure that there are no stuck buttons on the remote control. Press each button to make sure they are not stuck in the pressed position.
- Update Firmware:
- Check if there is a firmware update available for your TV. You can usually find this information in the TV's settings menu.
- Reset to Factory Settings:
- Perform a factory reset on your TV. This will erase your settings, so be sure to back up any important information first.
- Check for Physical Obstructions:
- Make sure there are no physical obstructions around the TV, particularly around the infrared sensor on the TV and the remote control.
- Contact Customer Support:
- If the issue persists and your TV is still under warranty, consider contacting Polaroid customer support for assistance. They may be able to provide additional troubleshooting steps or offer a solution.
- Professional Repair:
- If the TV is no longer under warranty and the issue persists, it might be advisable to consult a professional technician or a TV repair service to diagnose and fix the problem.
Always refer to your TV's user manual for specific instructions related to your model. If none of the above steps resolve the issue, it's recommended to seek assistance from the manufacturer or a qualified technician for further diagnosis and repair.
12/27/2023 10:15:57 PM •
Polaroid...
•
Answered
on Dec 27, 2023
•
42 views
Can you tell me the code for a Polaroid TV for SANSAI URC-L969 universal remote please.
First is a link to a codes page. Next is a description of programming the device. The code page strikes me a little confusing about the method so that is why I provide the description of programming.
Polaroid TV Universal Remote Codes & Program Instructions - Universal Remote Codes
- Turn on your Polaroid TV.
- Press and hold the SET button on your SANSAI URC-L969 universal remote until the LED light turns on.
- Enter the 3-digit code for your device using the number buttons on your remote. If you don't know the code, try searching for it online or contact the manufacturer of your device.
- Release the SET button once you've entered the code.
- Test if your remote is working by pressing some buttons like volume up/down or channel up/down.
10/28/2023 7:27:19 AM •
Polaroid...
•
Answered
on Oct 28, 2023
•
66 views
Not finding what you are looking for?