20 Most Recent Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher - Page 2 Questions & Answers

you will need to replace your touchpad.

Hello, dedelee I was trying to help you out here. I was going back to some customers that asked questions in the past and it appeared that no one answered them, so I thought I would take some of my personal time to see if I can help. Here is a link to about everything you want to know about your dishwasher, from repair to trouble shooting it,pictures, video's. Just scroll around and you will see tons of information to almost any question you might have on your dishwasher. If you go to this link and click around, I am sure you will find out so much about your dishwasher, you will know more that the company that made it. Here Is the link for you to click on>> http://home.howstuffworks.com/dishwasher.htm Please if this helped you at all, if you can find the time to rate my help and some kind words written would be appreciated for my free help , I would appreciate it. Here is also my direct link to my own pages of other areas of my expertise for other problems you might have in Automotive,Appliance, and Electronics. Drop In anytime for my help. Thanks,Mike http://beta.fixya.com/users/mc1bean

Hi,
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Waterwill not drain out

heatman101

Hi

"Er Clean S" is a common error with Frigidaire which means shorted keypad. The issue is with the touchpad/keypad that should be replaced, under warranty. However, before replacing the keypad you can unplug it and take it apart completely and use a hair dryer to blow some warm air on the keypad assembly to blow the moisture off but again doing this will void warranty so decide if you want to get this done under warranty or you want to do it yourself. Hope this helps...please post back for further assistance.

Daniel

Hi,

Here is a tips that I wrote that will help to explain why you get the PF Error Code

PF Error Code for Appliances

heatman101

-==-][][

Hi,

Here is a tips that I wrote that will help to explain why you get the PF Error Code

PF Error Code for Appliances

heatman101

,..,

Hi

Error CL appears when the dishwasher control detects door switch is open or door is open. You'll have to open the door and check the continuity of the door switch. If the door seems to be closed then it is the control has detected an issue with the door latch. Check the door latch & seals to make sure door is closing fine. Unplug the dishwasher from power outlet and wait for 10-15 minutes. Restart the dishwasher and check if the error is still there. If error still appears then you'll need to repalce the door switch/door latch. Hope this helps... Please post back for further assistance.

Daniel

The first thing I would check is the air gap. That is a silver or chrome thing on your countertop above the dishwasher. You can normally pull it off or twist it off. Look fore a plug. I have seen even a piece of popcon plugging it. Next check your drain line. If it goes into your garbage disposal make sure it is clear. Too many people do not run the hot water near there dishwasher before it is hot and then start the dishwasher. Todays dishwashers use very little water per EPA but need hot water to do the job.
Hope this helps

There may be a problem with wiring, that is blowing the timer board. Often this kind of problems are difficult to spot because the contact or short occurs with vibration during cycle.

To start check the board wiring, unplug and re-connect wiring.

Observe the board for burnt areas on the connectors, if you are lucky problem is in there.

Otherwise test wiring harness and connection to impeller pump, drain pump and inlet valve, check if any of them may short.

Your evaporator coils frost up in normal use and every eight hours or so the entire unit shuts down and the defrost heater comes on to melt the frost. This cycle last about 20 minutes. The melted frost drips into a drain pan and through a drain tube to the drain tray under the freezer/refrigerator where it's evaporated by the condenser fan.


Your drain tube may be stopped up with ice at the upper end because it drains too slow because it's stopped up at the lower end in the evaporator pan under the unit at the floor. It can get dust and mold in it. Once you get the ice out at the top a little pressure with a turkey baster will usually clear it out. Flushing it out with hot water and clorox may help.
Make sure it drains quick enough to prevent refreezing. . The drain should be located below the evaporator coils on the lower back of the freezer.

go with a kenmore reasonable price ....work very well and sears is very good re their appliances per warranty

pf is means power failure.

Hi, I am doing some Research at this moment. Will get back to you,
Shastalaker7