20 Most Recent AEG 23 in. Favorit 86070Vi Built-In Dishwasher - Page 8 Questions & Answers

Fault in heating phase. Could be: Heating element, wiring between heating element and power board, power board (usually relay). Sometimes can help to resoldering (cold solder joint) or replaced relay on power board. Dado

http://www.electrolux-ui.com/

There are several reasons if spray arms doesn't spray water. First you need to check efficiency of circulation pump. If it works, then should check the turbine of circulation pump. Sometimes turbine blades can be broken and the pump does not produce enough pressure to turn the spray arms. Be sure to check that the filter is not clogged which can also causes same problem. Finally, check that the nozzles of spray arms are not clogged. So, could be: - motor circulation pump - circulation pump - filter - spray arms - electronic or power board Dado

1. To remove upper basket spray arm, tilt it down hard. 2. Clean spray arms jets. 3. Place cleaned upper basket spray arm back in position against the connecting piece: press the two together firmly, until you feel them snap into place. Dado

Customer always needs to follow the manufacturer's instructions about cleaning and maintaining the appliance. If there are some ambiguities then you should contact an authorized service center. I personally believe that it is not a good idea to clean hob with steam cleaner. 6.3 Cleaning the hob • Remove immediately: melted plastic, plastic foil, and food with sugar. If not, the dirt can cause damage to the hob. • Remove when the hob is sufficiently cool: limescale rings, water rings, fat stains, shiny metallic discoloration. Clean the hob with a moist cloth and some detergent. After cleaning, rub the hob dry with a soft cloth. • To clean the enamelled parts, cap and crown, wash them with warm soapy water and dry them carefully before you put them back. Dado

Error code E49, generally speaking, at AEG dishwasher does not exist. Dado

AEG produced a lot of model dishwashers over several decades. Please, specify AEG model or product number. Dado

You must specify more symptoms than we can help you. It's just like going to the doctor and ask him why I'm sick. He needs more symptoms if you want to help you. Dado

The most common cause of a fault "i10" is closed valve on the water supply line. So this failure indicates a problem with filling of water. Possible error causes: Closed water tap, Inlet valve faulty, inlet hose bent, softener system clogged, pressure switch or pressure switch hose obstructed or leaking, wiring from pressure switch to printed circuit board (PCB), wiring from inlet valve to PCB and finally PCB. Dado

The problem when the dishwasher does not heat is failure which requires to remove the qualified personnel and therefore error code is not shown on the display but it is visible in the service mode. Possible error causes: faulty heating element wiring between heating element and PCB PCB (printed circuit board) Dado

It is possible, but definitely before check if something is obstructed or blocked the drain pump. Error "i20" means there is a problem with draining water. Dado

The most common cause of a fault "i10" is closed valve on the water supply line. So this failure indicates a problem with filling of water. Possible error causes: Closed water tap, Inlet valve faulty, inlet hose bent, softener system clogged, pressure switch or pressure switch hose obstructed or leaking, wiring from pressure switch to printed circuit board (PCB), wiring from inlet valve to PCB and finally PCB. Dado

Error "i30" means that water remains in base because leakage or overflow. In this case, in order to prevent flooding, drain pump running continuously. When we talk about AEG dishwasher, drain pump works even the power is turned off (must be connected to the wall outlet, otherwise anti-flooding system will not work). The noise what you heard during operation indicates that something is blocking the drain pump. Remedy: you should first remove the water from the bottom of the dishwasher and determine leakage then check why the drain pump makes noise. If you work around the dishwasher, you always take care that appliance must be disconnected from the power supply. Good luck. Dado

check that the screw is missing probably fallen in to the filter

have you tried cleaning you filters. this sometimes stops the machine from draining

Fault is associated with cylcling pump which pumps the water during washing. It sounds like it is only happening occasionally which could mean that the control board for cycling pump is faulty. If happening every time then pump may be faulty. This parts can be pretty pricey so if its only happening occasionally then you may want to consider living with it until it gets worse.

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/