20 Most Recent Whirlpool GHW9300 Duet Washer Questions & Answers


ERROR F11 (Whirlpool Duet GHW9300)

Hi there this is as it reads for your fault code F11

Serial Communication Error
Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.
  • Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)
  • Check the Drive system for any worn or failed components
  • Check MCU
  • Check CCU
  • Check Motor
  • Check Wire Harness
10/20/2020 7:48:17 AM • Whirlpool... • Answered on Oct 20, 2020


My washer is leaking what can be the problem
12/16/2018 11:16:41 PM • Whirlpool... • Answered on Dec 16, 2018

Whirlpool washer

If you open the top you will see a circular disc with a thin rubber tube attached to it. This is an air pressure switch that switched off the water supply when it reaches its level. When the machine is unplugged remove the tube from the switch and blow into it. It should be clear. Next blow into the little fitting on the switch , if the tube is ok ,and it should click. Either the switch is faulty or the tube is blocked,detached from the machine or burst. Hope this helps.
2/2/2016 11:31:29 PM • Whirlpool... • Answered on Feb 02, 2016

Whirlpool Duet washer - paused cycle to add a garment now can't get it to resume cycle or clear the cycle.

I did as Drunan did and unplug for 10 and plugged it back in and it started like a champ! Thanks!!!!!! ;)
10/30/2015 11:38:35 PM • Whirlpool... • Answered on Oct 30, 2015

Error code washing is delayed wil wash half the clothes

F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.

Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
7/10/2015 11:22:01 PM • Whirlpool... • Answered on Jul 10, 2015


Chek for water in the drum if so take out the filter and clean there will be lots of water so be carefully make sure machine is unplugged from mains
1/2/2015 9:51:54 PM • Whirlpool... • Answered on Jan 02, 2015

Diagnostic test

Be the first to answer 5/21/2013 3:18:06 PM • Whirlpool... • Posted on May 21, 2013Be the first to answer

Will not restart after adding clothes

Press and hold "end of cycle" button for 3 seconds, on the right side of panel. Wait for 2 minutes before trying the door. This is the child lock feature, do it again & it locks.

If helped, pl rate me good!!
1/29/2013 9:39:49 AM • Whirlpool... • Answered on Jan 29, 2013

Control locked light is on and will not

Press and hold the "End of Cycle Signal" button for approximately three seconds until the "Control Locked" indicator light shuts off.
11/7/2012 3:51:49 PM • Whirlpool... • Answered on Nov 07, 2012

Whirpool ghw9250

Be the first to answer 10/24/2012 3:45:36 PM • Whirlpool... • Posted on Oct 24, 2012Be the first to answer


see this causes and fix it. God bless youBelt, Water Pump If the washer won't drain the pump belt might have broken or might have worn out. Check the belt and replace if it shows signs of excessive wear. Clogged Pump or Hose If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Remove the hoses from the pump in order to remove the article of clothing. Keep in mind that any water in the washer will pour out of the hoses when removed. Drain Pump If the washer won't drain water the drain pump might be defective. It's also common for a small sock or other article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump. Drive Belt If the washer won't drain, should check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't drain properly, if at all. Lid Switch Assembly If the washer won't drain the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design. Door Lock Motor and Switch Assembly If the washer won't drain the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design. Drain Hose If the washer won't drain water check the drain hose. Be sure the hose did not get kinked behind the washer. Also, remove the hose from the pump and check it for obstructions. Coin Trap If the washer won't drain the coin trap may be clogged. This washer is equipped with a device near the water pump called a coin trap. The purpose of this device is to trap any foreign materials that make their way down the drain. Normally, the coin trap can be accessed through an access panel. It is designed with the homeowner in mind and is normally easy to clean out. 10_2_2012_1_02_28_pm.gif
10/2/2012 1:02:35 PM • Whirlpool... • Answered on Oct 02, 2012
Not finding what you are looking for?
Washing Machines Logo

94 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts


Level 3 Expert

85241 Answers

Brad Brown

Level 3 Expert

19166 Answers


Level 3 Expert

4383 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

duet Whirlpool

  • duet Whirlpool

Most Popular Question

duet washer fell off platform picked

  • Washing Machines