20 Most Recent Whirlpool WFW8300SW - Page 8 Questions & Answers

take bottom panel off should be 3 to 4 screws and will come off then you will see your drain pump in the middle in the center with a plastick cap you can take off. before you take off get plenty of towels ready because water will come out try leaning unit back until you dont have to hold it then take cap off and clear any debree you find and put cap back on and try running again offen to much debree can damage pump and might need to be replaced!

“Rinse,” “Cycle Complete” and “Add a Garment”
illuminated or “F21” on display (Drain Problem)
Select PAUSE/CANCEL twice to cancel the cycle. Unplug
washer or disconnect power.
Check the following:
Is the drain hose kinked?
Is the drain hose frozen?
Is the drain hose clogged?
Is the drain hose more than 96" (2.4 m) above the floor?

Any other Status light combination (Electrical Problem)
Select PAUSE/CANCEL twice to cancel the cycle. Select
DRAIN/SPIN if there is excessive water in the washer.
Re-select cycle and press START. If the problem remains, call
for service.

you have an article of clothing stuck between the tubs. run your hand around between the tubs and you will probably find something at about the 11:00 o' clock position.

Hi!

“F20” on display
(Water Inlet Problem—no water or insufficient
water supply) Select PAUSE/CANCEL twice to cancel the cycle
Unplug washer or disconnect power. Check the following: Are water faucets completely turned on?
Are screens at inlet hose connection to washer
clogged? Are water inlet hoses kinked? Are water inlet hoses frozen?
Do rate the solution.

Thanks
Rylee

unplug the unit for an half hour and plug it back.

brand new your not under warranty,,,this just came out....ok go to bacl and take scews from top out,slide top back remove...now remove the 2 screws on console bracket at each corner,,now look down inside front corners see thoses clips pry and pull and your console is off...onthejob

remove bottom and ck for 2 braces that may have been reinstalled they bolt from base to lower balance block remove them also ck the shocks to make sure they didn't get broke

if prvious owner has had no problems sounds like a good deal that is less that half new price no major issues most problems are customer instructs ..front loads are just catching on.. a lot of people don't fully understand them and with electronic controls they can be fickle..

Hi there!

You have to ask yourself how much is the warranty worth to you. You normally have a 12 months warranty because if the machine is going to develop a fault, it will usually be in the first few months of use.
Saying that, some brands just don't last that long. The ones that do are expencive to buy in the first place.

So to answer your question, if you are getting it for half price of new, then yes I would go for it. If in the event something does go wrong, a repair will still be cheaper than a similar new unit, so you haven't lost out on the deal.

If this provides the info you need, Please spare a moment to rate as Fixya! Thanks.

. HE detergent is a must for these machines first and foremost. as a genral rule liquid detergent breaks down better in cold water, so performs better in washers(cold water rinses). powder breaks down better in hot water which is why its reccomneded for d/w's.that being said i dont really mind which is used where so long as your not experiencing cleanig problems, at that point its when i reccomend using the appropriateone. whirlpool has now reccomneded a product called AFFRESH, tablets that can be used to clean out you frontloading machine incase of residual build op and/or odors.

There appears to be a solution here

Why has my whirlpool washer started asking me about

JustAnswer https://www.justanswer.co.uk > appliance > h42zj-whirl... Jun 24, 2021 - I dont have an error code. I set my washer to wash (press play) it senses then asks 'compartment II 53ml? I have to then press play again ... I have a whirlpool 6th sense zen 12 kg washing machine Jan 7, 2023 Error f24 on my machine, Whirlpool 6 sense I'm not sure how May 1, 2022 How do I remove demo mode from my whirlpool 6th sense 9kg May 13, 2021 My 6th sense Whirlpool dryer has stopped working. 2 red LED Jul 29, 2014 More results from www.justanswer.co.uk A little more here https://www.google.com/search?q=Whirlpool+6th+sense+is+displaying+this+message+Compartment+II+37ml ..

It won't be easy - the necklace went through the hole so logically it should come back, unfortunately it is the nature of a necklace to be a random structure unless some tension is applied; the links or whatever are apt to go sideways and jam in the hole. In an extreme case the necklace could be knotted... If it is knotted there is no chance of removal and the solution is either to dismantle the washer or to break the necklace. Positioning the drum so the necklace is under tension under its own weight and with some jiggling and the application of lots of patience and some luck it should come back through the hole.

What is the model number for this washer?

Check the Coin Mechanism: Ensure that the coin mechanism is functioning correctly. Sometimes, coins may get stuck or not register properly. Verify that the coin slots are clear and that the mechanism is engaging properly. If there's an issue with the coin mechanism, it could prevent the washer from starting. You might need to clean or repair it. Inspect the Wiring: There should be a harness with two wires that go into the coin mechanism box. Check if these wires are intact and properly connected. If you find any damage or loose connections, consider repairing or replacing the wiring. Bypass the Coin Mechanism: If you suspect that the coin mechanism is causing the problem, you can bypass it temporarily. Cut the wires going into the coin mechanism and insert a push button switch in the line. This will allow you to manually start the washer without relying on the coin mechanism. If you're unsure how to do this, consider contacting a local repair shop for assistance. Check for Other Issues: Inspect other components such as the lid switch, control board, and start button. Any malfunction in these parts could prevent the washer from starting. Make sure the washer is plugged in and that there are no tripped circuit breakers or blown fuses.

Check the suspension springs for stretching and shock absorber for operation. I am having difficulty finding that model. https://www.google.com/search?q=Whirlpool+Cabrio+wtw6707w2+washer%2C+UL+code ..

The F20 error code on a Whirlpool Duet Steam Washer typically indicates a water inlet problem. It means the washer is not getting enough water to continue the wash cycle. This can be due to several reasons, even if it seems like water is flowing fine at first glance. Here are steps you can take to troubleshoot and potentially resolve the issue:

1. Check Water Supply Hoses:
   • Ensure both the hot and cold water faucets are fully open.
   • Inspect the water inlet hoses for kinks, bends, or twists that could restrict water flow. Straighten out any issues you find.
   • Turn off the water supply, disconnect the hoses from the back of the washer, and check that the filter screens inside the water inlet valve are not clogged with debris. Clean them carefully if needed.
2. Water Pressure:
   • The washer requires a certain amount of water pressure to function correctly. Low household water pressure can lead to insufficient water flow to the washer. Make sure your home's water pressure is within the washer's required range.
3. Check for Siphoning:
   • Make sure the drain hose is correctly installed. The end of the hose should not be too far down the standpipe, and there should be an air gap to prevent siphoning.
4. Inlet Valves:
   • If the water hoses and screens are clear, there might be an issue with the water inlet valves themselves. They might not be opening fully due to electrical issues or mechanical failure.
   • The inlet valves can be tested with a multimeter for continuity to ensure they are functioning correctly. If they lack continuity, they need to be replaced.
5. Flow Meter:
   • Some Whirlpool Duet models have a flow meter that measures the amount of water entering the washer. If this component malfunctions, it could mistakenly signal that there's not enough water, even when there is.
   • Diagnosing a flow meter requires some technical knowledge and a service manual for your specific model.
6. Pressure Switch:
   • The washer uses a pressure switch to monitor the water level. If there's an issue with this switch or the hose connected to it, the washer might incorrectly interpret the problem as insufficient water flow.
   • Check the pressure switch and the hose for any blockage, disconnection, or damage.
7. Reset the Washer:
   • Since unplugging the washer hasn't cleared the error, after checking the above, try to reset the control board by unplugging the washer for about 5 minutes, then plugging it back in.

If after trying these steps the F20 error persists, it may be time to consult the manual for more specific troubleshooting steps for your model or contact a professional appliance repair service. Sometimes, the problem could be related to the washer's electronic control board or other components that require professional diagnosis and repair.

Is the correct tension on the belt; too much and the bearing could be getting damaged. If you remove the belt, check the drum moves freely with no noise. If noisy, replace the bearing or purchase a new machine.

Stale smells come from not drying the front gasket trough just inside the door. Your bleach isn't cleaning that area. Use Tilex Mold spray on it. Clean and dry the door glass as well and leave the door open for a few hours after a wash or leave it open all the time. If it is dry, it can't smell.There will always be some water in the pump area, but if you remove the pump filter cover, that releases and water left behind.When you use bleach always do whites or your tea towels next. You can also dilute by adding a couple of jugs of water first.There is a trick to look for rattling items between the inner and outer drum. Put a good flashlight against the holes in the drum and you can see what is below without getting the glare from the drum.These websites give you a full parts schematic showing all the parts and their positions.https://www.appliancepartspros.com/tub-basket-parts-for-whirlpool-wfw94heaw0.htmlWhirlpool Washer WFW94HEAW0 - OEM Parts & Repair Helppartselect.cahttps://www.partselect.caCanada Wide Same-Day Shipping For All In-Stock Parts. Shop Canadian And Avoid Customs ' 2 Million Parts Ready To Ship. OEM Parts & Accessories. One-Year Warranty. Money Back Guarantee. Free Repair Help & Videos. Types: Dishwasher Parts, Dryer Parts.