20 Most Recent AEG Lavamat W1450 Front Load Washer - Page 7 Questions & Answers

The machine knows what the water level should be at every step of the program, so if its full when it should be empty, is not filling when it should be or is taking too long to fill or empty the program will abort and count down in seconds as you describe. First - check the drain filter for blockage!! if clear, can you hear the drain pump running on 'drain' program? a chug chug chug noise. If not pump may be jammed or seized - or the drain tube maybe be blocked at the waste connection on the sink, etc. Or maybe the water supply pipes have blocked or got turned off? Possibly the waste pipe may not have been installed correctly and the machine is syphoning empty? ie the end of the waste pipe is lower than the water level in the machine - so it syphons empty like draining petrol from a petrol tank! That would empty the machine when it should be full. Check all the basics of filling, draining and filter before suspecting anything else.

Check your pressure sensor. Make sure that the air column that operates the pressure sensor is not blocked. Find the pressure sensor and remove the air hose to it. Blowing into it with the hose attached to the pressure sensor will check the pressure sensor. Use an ohm meter to measure if it changes. Blowing on it with it connected to the air column will check that nothing is blocking it.

This sounds like it is the heating element in the machine. Check to make sure the heating element is getting power. If it is then replace the element.

This could be a number of issues. Have you checked the brushes? They should be at least 15mm. Check your circuit board and make sure that the dust from the brushes did not attach itself to the board and cause a short. Use compressed air to clean the motor. Clean the circuit board with air if dirty. Check for solder joints on the circuit board to see if any cold solder joints on the relays.

Is it plugged in? Is the water on? Is the door closed?

Open the machine up on the top lid. 2 screws at the back of the machine at the top. Slide the lid back and remove it. The drawer can now be accessed. There should be a bunch of clips holding the lid of the drawer . You can carefully open these clips to remove the lid or just remove the entire drawer assembly and replace it or try to figure out what is jamming it.

5.18 Child lock function This function prevents children operating the control panel. • To activate this function, touch button 12 and button 11 at the same time until the display shows the symbol . • To deactivate this function, touch button 12 and button 11 at the same time until the symbol goes off. You can activate the function: • Before you touch the button 6 : the appliance cannot start. • After you touch the button 6 , all the buttons and the programme knob are deactivated. Display: Dado

go to the manufactures website and download the user manual for advice on error codes eric

my best advice is to call the engineer for a quote as there's obviously a problem in the making after further use eric

go to the manufactures website for help this is a washing machine help website eric

Im sorry to say that you will need to cal the AEG engineer for a quote as the display cannot be black, it should display some information on start up anyway eric

try replacing the fuse in the plug that's often overlooked eric

there is no easy way to do this as the service manual does not list the component on the board the only thing you can do is go to a scrap yard to try and find a similar machine and find the missing parts on it please be careful don't forget its 230 volt mains that can be lethal to the inexperienced person eric

AEG Dishwasher Common Error Codes ' RemoveandReplace.com

HI Mike. THIS IS ALL I COULD FIND OUT. E40 relates to the door being left open when the programme is started, it maybe that the latch was not pushed over when the door was shut. to solve the problem get another switch. hope this helps you. or read up some more at this link. washing machine AEG Lavamat turbo 16800 it displays E40 Google Search

Here is the source. You have to create an account before you can get the requested documents. Support

to clear the error code: whilst holding the pre wash and short wash buttons in together turn the control knob from off to gentle spin, this will clear the fault code and run a LED test. (if all goes weel) F9 means carbon brushes need to be replaced