20 Most Recent Pioneer AVIC-D2 DVD Nav/6.5" Screen/AM/FM/CD Player Car Video Player - Page 3 Questions & Answers


Hi i purchased the upgrade

to access the nav dvd press the open button for a few seconds. then you should be able to eject the old disc and insert the new one.
12/23/2010 5:50:11 PM • Pioneer AVIC-D2... • Answered on Dec 23, 2010

Update dvd

type this on ebay, is way cheaper than pioneer websitePIONEER AVIC CNDV-80MT 2008 GPS MAP DVD
12/8/2010 8:58:56 PM • Pioneer AVIC-D2... • Answered on Dec 08, 2010

The map and driving direction keep recalculating

In the navi menu you can choose to avoid highways. as well as choose fastest route. i allways choose th have multipal routs. if that dont work go to the menu and reset radio to factory defaut settings
12/8/2010 8:36:10 PM • Pioneer AVIC-D2... • Answered on Dec 08, 2010

I have a mustang 2009 and added a aftermarket

The Mustang use a 6 volt remote turn on so you need to reduce the voltage by adding 2 resistors. Get two 10ohm resistors and tie the top end together and that will be the out put to the car. The other side will have two wires one is the positive remote from the radio and the other goes to ground. It shouldnt pop then.

11/10/2010 12:41:35 AM • Pioneer AVIC-D2... • Answered on Nov 10, 2010

My cds/radio plays fine.. my

the disc you are using are either incompatable or may be dirty.
9/14/2010 6:59:46 AM • Pioneer AVIC-D2... • Answered on Sep 14, 2010

There is no picture from

You need to check the power for your camera.The positive at the reverse light works well. Yo0u also need to go in the menu and make sure the avic unit is programed for the camera. And check to make sure you are pluged into the proper port.
9/5/2010 2:31:40 AM • Pioneer AVIC-D2... • Answered on Sep 05, 2010

How do you connect a pioneer d2 navigation system to a 2006 ford expedition entertainment system

You need to identify the four wires that carry the DVD audio in the factory plug, and re-wire them to RCA plugs that can be used with the Auxiliary input RCA jacks on your Pioneer unit. The four wires should be: Left (+) light green Left (-) white Right (+) red Right (-) black The easiest way is to purchase some inexpensive RCA cables (or better yet, speaker wire with RCA ends). Cut the cables and wire the center pin conductor wires to the (+) audio wires in the stock plugs, and connect the outer shield conductors to the (-) wires. Then connect the RCA plugs to your head unit's auxiliary input jacks.
8/27/2010 4:39:49 PM • Pioneer AVIC-D2... • Answered on Aug 27, 2010

I bought a Pioneer AVIC-d2

la pantalla del Pioneer AVIC-D2. ha perdido la iluminacion
8/25/2010 8:42:30 AM • Pioneer AVIC-D2... • Answered on Aug 25, 2010

I have a 2006 AVIC-D2 - navtraffic - pioneer. The

contact pioneer at 1-800-746-6337 for a authorized repair facility. I seen this problem on some unit's and needed to send them out for repair. i believe it was a $150 flat rate for repair
6/16/2010 12:10:35 AM • Pioneer AVIC-D2... • Answered on Jun 16, 2010

Avic-d2 question

sometimes i notice the touch screen calibration is a little bit off...Try to push the okay button a little bit to the left or right working your way from the okay button to the edge of the screen
6/8/2010 12:15:48 AM • Pioneer AVIC-D2... • Answered on Jun 08, 2010

When i insert a dvd, the display say ERROR 12 why?

bad dvd drive, sorry
5/12/2010 10:52:20 PM • Pioneer AVIC-D2... • Answered on May 12, 2010

Pink wire whats it for, it on a pioneer avic-d2

The brake sensor wire (Lt Green) can be simulated with a toggle switch to ground.
The mobile navigation system is connected here to detect the distance
the vehicle travels. Always connect the vehicle’s speed detection
circuit or the ND-PG1 speed pulse generator, sold separately. Failure
to make this connection will increase errors in the location display.
To lighting switch terminal

Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch. If this connection is made incorrectly or omitted, certain
functions of your navigation system will be unusable.

This is connected so that the navigation system can
detect whether the vehicle is moving forwards or
backwards. Connect the violet/white lead to the
lead whose voltage changes when the shift lever is
put in reverse. Unless connected, the sensor may
not detect your vehicle traveling forward/backward
properly, and thus the position of your vehicle
detected by the sensor may be misaligned from the
actual position.
Note: When you use the ND-PG1 speed pulse
generator (sold separately), please make sure
to connect this lead.
When you use a rear view camera, please make
sure to connect this lead. Otherwise you cannot
switch to rear view camera picture.

Further detail can be found here:
2/24/2010 11:59:54 PM • Pioneer AVIC-D2... • Answered on Feb 24, 2010
Not finding what you are looking for?
Pioneer AVIC-D2 DVD Nav/6.5" Screen/AM/FM/CD Player Car Video Player Logo

Popular Tags

103 questions posted

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio & Video Experts

 Francisco Mauricio...
Francisco Mauricio...

Level 3 Expert

1551 Answers

The Knight
The Knight

Level 3 Expert

76823 Answers


Level 3 Expert

13435 Answers

Are you a Pioneer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Pioneer Car Audio & Video

  • Pioneer Car Audio & Video

Most Popular Question

l radio in japenese speak english

  • Car Audio & Video