Pioneer PDP-5060HD 50 in. Plasma Television - Answered Questions & Fixed issues
Pioneerpdp506pe
No. It is somewhat skilled work. If you wish to get more details about Y-board replacement to Plasma displays,
check this link.
2/11/2013 3:42:49 PM •
Pioneer...
•
Answered
on Feb 11, 2013
•
61 views
Hi, my input 2 does
Check your connections especially the yellow RCA connector. If it is a scart connection the video pin may be broken change out the lead for a new one
3/6/2011 1:15:45 PM •
Pioneer...
•
Answered
on Mar 06, 2011
•
234 views
PLASMA DISPLAY STARTING UP. PLEASE WAIT
Un plug the power to the Plasma Screen and also to the Media Receiver for ten minutes. Disconnect the off the air antennas both A and B. After ten minutes plug in the plasma screen then the media receiver and turn on wi the remote control. You should now be back in operation. I was.
Also It may not be a bad digital tuner. The TV Guide feature is active even when the zip code is set to all 0s so if you have an over the air antenna attached the TV will look for the TV Guide info and if it can not find it because of a weak signal or the chanel it is tuned to does not carry that information the TV thinks that tuner does not work which triggers the 12 flashes. Also on power up the gray box with the waring message "Plasma Display Starting Up, Please Wait" appears and the screen is blank.
12/3/2010 5:25:07 AM •
Pioneer...
•
Answered
on Dec 03, 2010
•
9,243 views
I have a Pioneer Elite
What you have done is change the input source. It will toggle through various modes like component, HDMI1, HDMI2, S-video etc., You should take a look behind the tv and see which input you have connected it into(usually HDMI 1 or HDMI2) then keep pressing the input button till it toggles back to that particular input.
Sai.
7/6/2010 5:20:16 AM •
Pioneer...
•
Answered
on Jul 06, 2010
•
978 views
My pioneer plasma PDP 5060HD Media Center control
lenwas,
I have the exact same problem with the same model tv. It just stopped working, tv has no lights or evidence of power and the red standby light on the media center flashes without any other function potential.
I checked the internal tv fuse and it was measuring continuity.
If you figure anything out I'd be interested to hear it.
Tom
3/5/2010 8:24:15 PM •
Pioneer...
•
Answered
on Mar 05, 2010
•
859 views
PLASMA DISPLAY STARTING UP. PLEASE WAIT
Un plug the power to the Plasma Screen and also to the Media Receiver for ten minutes. Disconnect the off the air antennas both A and B. After ten minutes plug in the plasma screen then the media receiver and turn on wi the remote control. You should now be back in operation. I was.
Also It may not be a bad digital tuner. The TV Guide feature is active even when the zip code is set to all 0s so if you have an over the air antenna attached the TV will look for the TV Guide info and if it can not find it because of a weak signal or the chanel it is tuned to does not carry that information the TV thinks that tuner does not work which triggers the 12 flashes. Also on power up the gray box with the waring message "Plasma Display Starting Up, Please Wait" appears and the screen is blank.
4/13/2009 3:58:41 AM •
Pioneer...
•
Answered
on Apr 13, 2009
•
4,210 views
TV Guide System not working
In order to receive the TV's Guide system, the cable should be connected directly to the TV instead of the cable box if you are still using it.
How do you have the cable box connected to the TV?
5/13/2012 11:21:27 PM •
Pioneer...
•
Answered
on May 13, 2012
•
1,158 views
Screen Picture is Cut off
did you try pushing the input key on your remote it might change the screen if that don't work then try to go in to the settings in the remote
11/9/2008 4:55:46 AM •
Pioneer...
•
Answered
on Nov 09, 2008
•
610 views
Picture but no sound.
What about in the menu,,most the newer tvs have got were you can turn the speakers off,, or if there a digital dts plug on the back,, the menu could be switched to digital instead of analog,, good luck
10/5/2008 1:57:30 PM •
Pioneer...
•
Answered
on Oct 05, 2008
•
141 views
Plasma Display Starting Up
Could be heat build up in the Plasma display unit. Make sure it has the correct space around it for proper ventilation. Also count the number of blinks on the power indicator it is a code for the reason the unit shut down. On the Pioneer PDP-5060HD I have I was getting 12 blinks on the indicator which indicated a tuner issue. Check your instruction book for info on the over heating problem if it continues. You may have a fan out.
5/24/2008 8:26:57 PM •
Pioneer...
•
Answered
on May 24, 2008
•
702 views
Screen frozen
Un plug the power to the Plasma Screen and also to the Media Receiver for ten minutes. Disconnect the off the air antennas both A and B. After ten minutes plug in the plasma screen then the media receiver and turn on wi the remote control. You should now be back in operation. I was.
Also It may not be a bad digital tuner. The TV Guide feature is active even when the zip code is set to all 0s so if you have an over the air antenna attached the TV will look for the TV Guide info and if it can not find it because of a weak signal or the chanel it is tuned to does not carry that information the TV thinks that tuner does not work which triggers the 12 flashes. Also on power up the gray box with the waring message "Plasma Display Starting Up, Please Wait" appears and the screen is blank.
2/20/2008 2:47:26 AM •
Pioneer...
•
Answered
on Feb 20, 2008
•
704 views
Cant get picture
Un plug the power to the Plasma Screen and also to the Media Receiver for ten minutes. Disconnect the off the air antennas both A and B. After ten minutes plug in the plasma screen then the media receiver and turn on wi the remote control. You should now be back in operation. I was.
Also It may not be a bad digital tuner. The TV Guide feature is active even when the zip code is set to all 0s so if you have an over the air antenna attached the TV will look for the TV Guide info and if it can not find it because of a weak signal or the chanel it is tuned to does not carry that information the TV thinks that tuner does not work which triggers the 12 flashes. Also on power up the gray box with the waring message "Plasma Display Starting Up, Please Wait" appears and the screen is blank.
2/20/2008 2:46:33 AM •
Pioneer...
•
Answered
on Feb 20, 2008
•
220 views
BLUE POWER LIGHT
Un plug the power to the Plasma Screen and also to the Media Receiver for ten minutes. Disconnect the off the air antennas both A and B. After ten minutes plug in the plasma screen then the media receiver and turn on wi the remote control. You should now be back in operation. I was.
Also It may not be a bad digital tuner. The TV Guide feature is active even when the zip code is set to all 0s so if you have an over the air antenna attached the TV will look for the TV Guide info and if it can not find it because of a weak signal or the chanel it is tuned to does not carry that information the TV thinks that tuner does not work which triggers the 12 flashes. Also on power up the gray box with the waring message "Plasma Display Starting Up, Please Wait" appears and the screen is blank.
11/13/2011 9:42:22 PM •
Pioneer...
•
Answered
on Nov 13, 2011
•
1,178 views
Timer on television
The user manual is available here:
Pioneer website - PDP5060HDSetting of the sleep timer is on page 58, quote:
You can also use the menu to set the Sleep Timer.
1 Press HOME MENU.
2 Select “Sleep Timer”. ( / then ENTER)
3 Select the desired time. ( / then ENTER)
4 Press HOME MENU to exit the menu.
2/3/2008 10:56:31 AM •
Pioneer...
•
Answered
on Feb 03, 2008
•
443 views
Not finding what you are looking for?