20 Most Recent Amana NAV8805EWW 3.3 Cu. Ft. Elustra Tub Washer Questions & Answers

Amana NAV8805EWW... | Posted on Jul 25, 2017 | Be the first to answer

Amana NAV8805EWW... | Posted on Jul 01, 2017 | Be the first to answer

Amana NAV8805EWW... | Posted on Mar 05, 2017 | Be the first to answer


it's the timer or the capacitor,most likely it will be the timer,i've very rarely seen the caps go bad

Amana NAV8805EWW... | Answered on Aug 13, 2015

Amana NAV8805EWW... | Posted on Mar 07, 2015 | Be the first to answer


Is the hot water Faust turned on also the filter in the end of the hose connected to the hot water may be plugged with lime or sediment

Amana NAV8805EWW... | Answered on Sep 13, 2014

Amana NAV8805EWW... | Posted on Apr 09, 2014 | Be the first to answer

Amana NAV8805EWW... | Posted on Feb 21, 2014 | Be the first to answer

Amana NAV8805EWW... | Posted on Dec 18, 2013 | Be the first to answer


How about trying other options - regarding spin and temperature.

Amana NAV8805EWW... | Answered on Apr 24, 2013

Amana NAV8805EWW... | Posted on Apr 17, 2013 | Be the first to answer


1. remove rinse aid dispenser from top of agitator, if present.
2. remove bolt in center of agitator, if present, if not, proceed.
3. pull up the agitator.

Amana NAV8805EWW... | Answered on Feb 07, 2013


If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

Check this link to replace the inlet valve:

http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:
http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Amana NAV8805EWW... | Answered on Jan 25, 2013

Amana NAV8805EWW... | Posted on Nov 28, 2012 | Be the first to answer


does it come from the door or underneath if from the door either there is to much washing in and the weight pushes against the door and water comes out or the door seal has gone if from underneath its one of the pipes that cary the water to the pump either a hole or small split should be easy to check if you take the back off washer also check pump motor is clear or in my house my wifes under wires from here bra;s have a tendancy of comming through the pipes haha hope this helps ivan

Amana NAV8805EWW... | Answered on Sep 24, 2012


regular ge washers just pull straight up. harmonys are lg's though.

Amana NAV8805EWW... | Answered on Sep 17, 2012


It sounds as if you are using WARM water for the wash cycle since your complaint begins with the rinse cycle. The rinse cycle generally uses COLD water, so I must deduce that your washer is not filling up for the rinse cycle. The humming sound is likely coming from the fill valve being starved for cold water.
Investigate your cold water supply to the washer and if you have good supply, you may want to replace the fill valve.

Let me know what you find...Thanks for contacting FIXYA.com

Amana NAV8805EWW... | Answered on Jul 15, 2012

Amana NAV8805EWW... | Posted on Feb 29, 2012 | Be the first to answer

Amana NAV8805EWW... | Posted on Oct 07, 2011 | Be the first to answer


This washer has a belt. The belt drives the pump on this washer. The motor turns in both directions. iIn one direction the washer tub is locked and the tranny agitates. The water pumps out and the tub spins in the other direction. If that pump is locked up or the hose from tub to pump is blocked then it wont pump the water out. Lay the drain hose down towards a bucket and see if any water comes out. If not you got blockage. Once you drain it out tip is back and remove the belt (no tools needed) turn the pump both directions and look for signs of a failed pump. Manual and more

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Amana NAV8805EWW... | Answered on Jun 30, 2011

Not finding what you are looking for?
Amana NAV8805EWW 3.3 Cu. Ft. Elustra Tub Washer Logo

88 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Amana 3.2 cu. ft. Top-Load Washer
Amana 3.2 cu. ft. Top-Load Washer

196 Questions

Amana ALW480DA Top Load Washer
Amana ALW480DA Top Load Washer

158 Questions

Amana DLW330RA Top Load Washer
Amana DLW330RA Top Load Washer

46 Questions

Amana ALW880WH Top Load Washer
Amana ALW880WH Top Load Washer

45 Questions

Amana NAV5800A Top Load Washer
Amana NAV5800A Top Load Washer

52 Questions

Top Amana Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4372 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Amana Washing Machines

  • Amana Washing Machines

Most Popular Question

remove aggitator in ge wash machine

  • Washing Machines
Loading...