20 Most Recent Balance CM2015 15" LCD Monitor Questions & Answers


If you wish to get some details; check the site linked here. Viewing it in "Mosaic" will make surf easy Pull up older posts. Surf the site with patience.
http://electronicshelponline.blogspot.com/

Balance CM2015... | Answered on Apr 17, 2014


If your LCD TV or monitor has stopped working, or is displaying one of the following symptoms, then it's a candidate for some new capacitors
- Flickering screen
- Screen image disappears after several seconds
- Dim screen
- Slow start
- Power LED on, but no picture
- Unusual colors and/or lines
The primary cause of LCD TV and monitor failure is caused by faulty capacitors. You can examine the capacitors in your LCD TV or monitor and actually see if they are bad.
If they appear bulged on top, then they need to be replaced.
New capacitors will solve a host of problems in LCD monitors and TV's and will extend the life of your monitor or TV by several years.
Check the cables, connectors and connections.
Take it to a repair shop.

Balance CM2015... | Answered on Apr 13, 2014


You need to change the input signal, get into the menu on your monitor and change the signal from rgb to dvi, hdmi or vga dipending on what cable you using for connection.
There is NO rgb connector on that monitor

Good luck

Balance CM2015... | Answered on Jun 30, 2011


You do not really need the driver for the monitor for it to work with any PC, the only time you need the driver is when all the resolution are not listed when you try to adjust the resolution, it is really bad if you run windows 7 since a lot of companies will not provide windows 7 drivers for old monitors. You need to use Fn key combination with with either F4,5, 6, or 7 to select internal/external/both which depends on the make and model of the laptop.
The monitor work OK with desktop PC?

I repair hundreds of monitors and I would have gone crazy installing ALL the drivers for ALL the monitor I have to repair.

Please leave rating if it helps.

Basic LCD monitor and TV troubleshooting guide:
http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide
http://www.fixya.com/support/r7406380-tv_training_manuals
Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you.
Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

Balance CM2015... | Answered on Jan 22, 2011


The fuse (surface mounted) may have been blwon by the wrong power supply being used, at least open it up and inspect the inside. Post pictures if you can for further help.
http://s807.photobucket.com/home/budm/allalbums
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net

Balance CM2015... | Answered on Jun 03, 2010


I would look for bad caps in the power supply first.
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague

http://www.badcaps.net

Balance CM2015... | Answered on May 13, 2010


Hello
before telling you the problem , check whether the cord into the cpu is not loose.if it is , then re-insert tightly, but if the connections are fine , i am afraid there is a bad news for you.
This is a failure in the active matrix or its driver i.c. If the unit is out of warranty the cost should be between $80.00 and $180.00 to fix this depending if the active matrix is the cause.Call your costumer support as they only can replace this component

Hope your Monitor is in guarantee period and
Good luck

Balance CM2015... | Answered on Apr 11, 2010


Could be one of two things: The power supply for the monitor has a loose connection and as soon as it starts heating up the connection is open. Or your video card could be going bad. I'd bet on the former, though.
Why not try swapping out the monitor for one from a friend and see if the problem persists?
If it does, either get the monitor fixed or replace it.

Balance CM2015... | Answered on Dec 13, 2009


check your monitor's vga cable, it may be corrupted.

Balance CM2015... | Answered on Sep 19, 2009


check the speaker at the back pannel of your monitor..

Balance CM2015... | Answered on Jun 24, 2009


This indicates the LCD inverter in the display is dead. If you have any experience with computer repair, replacing an LCD Inverter can be easy enough; However, it may not be worth it for a 15" LCD; replacement inverters can cost anywhere between $15 and $40 - a decent used 15" LCD only costs about 40 bucks these days...

Balance CM2015... | Answered on Feb 13, 2009


http://members.driverguide.com/driver/detail.php?driverid=564775

I'm not sure where you found your driver, but this is from another website, hope itworks

Balance CM2015... | Answered on Dec 13, 2008


adjust your screen resolution

Balance CM2015... | Answered on Dec 05, 2008


I used to repair LCD monitor from Dell. It works. Most of LCD monitor brand have the save main components such as CCFL lamps, inverter board, power board. You might be using these following steps to examine what wrong with your monitor. After you turned PC on and monitor stopped working or went black, you have to check that if you can see the image on the screen or not by shining a flashlight into the screen, not directly but find the best angle to the screen and take a look very closely. If you can see the icons or any image (Start menu), there will be a minor problem. This is because of CCFL lamps inside screen. Some of them were broken and it is very easy to replace. If you cannot see anything on the screen, there'll be some problems with inverter board. If you have soldering tool and want to fix it by yourself, check the caps first. It may cause this problem. Some caps might show leaking or burn spot on the board because of too high temp. If you don't have soldering tool, you better go get a technician to do so. Hope this help!! If anything I can help you with, feel free to let me know.
Thank you,

Balance CM2015... | Answered on Nov 23, 2008


I bought this monitor brand new and as I recall there was no software in the box.

Balance CM2015... | Answered on Oct 18, 2008


Do you have it connected to a laptop? Or maybe your system is set to go into hibernation. Go into control panel and look for power settings. In there you will find a setting which turns monitor off after a certain length of time. Either set it to not turn off or set the period longer. If you are using it with a laptop you have to compromise between wasting of battery power and ease of usage. This is common on laptops although it is sometimes a problem with desktop machines. I doubt whether it is a monitor hardware problem. I am presuming your monitor goes off after a period of inactivity.

Balance CM2015... | Answered on Sep 26, 2008


plz check sound with speaker if there is sound then u can check or change cable that you are inserted in monitor plug .if it is ok then problem is related with monitor sound ckt plz change ic related with sound section

Balance CM2015... | Answered on May 10, 2008


How old is your PC. If it is old maybe your graphics card is ********** to run this game. It is probably not the monitor itself but the way the computer is handling the graphics. Have a look on the box the barbie game came in and see what version of directX it needs. If it is directX 9 and your computer is a couple of years old then your graphics card needs updating. Because you can hear the game indicates that the computer is running it OK but that it is having difficulty representing the images on the screen. If none of the above applies then we need more information on your system. Model number, manufacturer etc.

Balance CM2015... | Answered on Mar 09, 2008


hi there, check your video cable, most of it has a broken cable. ty

Balance CM2015... | Answered on Dec 26, 2007


Sometimes over long periods of tiem these buttons on the LCD monitor become lodged and they begin to stick. From frequent use the board that controls these small charges that allow the board on the mother board to know what button is pushed shortout or go bad, the pads beneath them go bad as well. You may want to purchase a new monitor! I repair these all of the time, sometime you just have to say goodbye! Sorry!

Balance CM2015... | Answered on Nov 28, 2007

Not finding what you are looking for?
Balance CM2015 15" LCD Monitor Logo

Popular Tags

35 questions posted

Ask a Question

Usually answered in minutes!

Top Balance Computers & Internet Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18438 Answers

NOEL
NOEL

Level 3 Expert

8546 Answers

Are you a Balance Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Balance Computers & Internet

  • Balance Computers & Internet

Most Popular Question

random shutdown

  • Computers & Internet
Loading...