I searched for a solution to an error code coming up on my Amana front load washer and got this site. Can anyone give a suggestion on how to get this error fixed. The washer still runs but seems to pause more and take longer to complete a load of clothes. Sometimes they spin out and sometimes they are wetter.
Posted by rikzmom7 on
5d means you're using too much detergent.
Posted on Jul 22, 2008
My washer is on and throughout the whole cycle it is continuously beeping and blinking the E2 error code. Does anyone know what this means? This code is not in the book. I'm hoping its not the same as the 2E one i had when the replaced the Electronic Control Board.
Posted by Anonymous... on
The first time my E2 code came on the washer won't rinse or spin. I checked the drain pump to make sure it was working. (1) Take the back off and pull the two drain lines off pump. Be careful the line going to the drain has a backflow flap, make sure you don't tear it.
(2) On the other side where it drains from the washer to the pump is where I found a bobbie pin that had collected lint and was blocking the drain flow.
When it can't drain the E2 code comes on to let you know it won't rinse or spin.
Make sure to unplug machine before removing back,
Hope this helps everybody with E2 problems.
Posted on Jan 09, 2008
maytag 4000 series error code F28 door lock.
Posted by jimswiders... on
Thanks for using FixYa. Please post a comment with the model no# for your Maytag 4000 series washer so that I can assist you further.
Posted on Jun 01, 2010
Washer cut off after completing cycle and door will not open. I know I can manually open it but how how do I fix problem so it won't happen again?
Posted by domino14 on
Remove the lower front panel.Reach up inside near the latch. Feel for a ring tab. Pull it down firmly while pulling on the door.
Then open the cabinet and check all the wire connections in the latch circuit. Check the wax motor ohms. The wax motor probably needs replacing.
Posted on Apr 15, 2009
My Maytag front loading washer MAH4000AWW will not drain?
Posted by jpf1 on
Check for obstruction in pump located at back of machine. Remove back panel and pump will be located on left hand side.
Posted on Feb 23, 2009
What does the F30 code mean on my Maytag washer?
Posted by karenafm on
I just spoke to a repairman who claims he's been working on Maytag washers for twenty years and has never heard of an F-30 error code. He says all Maytag error codes are four digits, and this isn't a real thing. Like I'm lying. While he's saying this, I'm watching the F-30 code flash on my machine. My God, you can't find anybody who knows how to fix anything any more...
Posted on Jan 17, 2017
I need assists on how to fix a LO error code on a Maytag Neptune front load washer. I will continue to click like its trying to lock but never does. It was in mid cycle and just stopped.
Posted by dave... on
Not really bad news. The unit requires a door lock assembly.
Posted on Feb 23, 2009
RECEIVED E2 ERROR CODE NOW CANNOT MOVE CONTROLS, TRYED TO RESET BY UNPLUGGING AND THEN HOLDING START BUTTON FOR 5 SECONDS, WAS TOLD BY ANOTHER MAYTAG CANADA REP TO DO THIS.
Posted by rcampeau4 on
I have only worked on USA machines but I believe you have a control panel error.
Posted on Oct 15, 2008
My Maytag Neptune washer (2002 model) has a problem with the door lock. The door lock is stuck and I have wet clothes in there! I tried unplugging it but it is still locked! It displays a "door open" error message
Posted by mrs_mjh on
Try these steps:
1.) Take the washer outside. 2.) Loosen the two screws on the back panel and remove the back panel. The pump sits on the left-side of the opening. There's a black water hose with a metal clamp; 3.) squeeze the metal clamp with your fingers until it's loose enough to slide away from the pump. 4.) Separate the hose from pump and the trapped water will pour out and the door will then open; and 5.) clear any blockage from the drain hose and the pump.
Posted on Jul 10, 2009
At the end of the wash cycle there is a large amount of water left in the tub. I can hear water being pumped out during the normal wash cycle. Any ideas, I'm thinking the timer?
Posted by jammert on
If you are saying that after the washer has finished you are left with wet cloths and water left standing in the tub ,then your pump is broken or as was my case I opened the back and removed the pump only to find a small piece of wicker that had come off my laundry basket . It was keeping the pump from turning .I removed it put everything back in place and saved over $380.00 . I hope this helps good luck .
Posted on Apr 08, 2009
520 questions posted
Usually answered in minutes!