20 Most Recent Maytag Neptune MAH6700A Front Load Washer - Page 6 Questions & Answers

0helpful
2answers

My Maytag Neptune washer has "np" flashing. The door is locked and the cycle is not complete

Are you sure this is not an nd and not an np flash code? If so then the code stands for no drain, likely something is clogging the washer pump inlet.
8/22/2016 5:55:10 PM • Maytag Neptune... • Answered on Aug 22, 2016
0helpful
1answer

The door wouldn't open we found the manual release opened it hoping to start the load of clothes again. The lights go on but the machine doesn't start a cycle. Any suggestions?

Make sure that the door switch is closing properly. If not, and it is stuck in the "open" position, the unit will not operate. Try bypassing the switch to see if it then runs.
6/20/2016 1:26:46 AM • Maytag Neptune... • Answered on Jun 20, 2016
0helpful
1answer

What is the cubic feet

5/23/2016 5:15:01 AM • Maytag Neptune... • Answered on May 23, 2016
0helpful
1answer

The dryer does not heat. does it need a new control panel?

Probably not. dryer no heat, first check the thermal fuse, then the ignitor. If the heating is intermittent, check the gas solenoid coils. In any case, be sure the entire exhaust duct is clean
5/2/2016 2:08:31 PM • Maytag Neptune... • Answered on May 02, 2016
0helpful
1answer

Dryer does not heat

Model number? Gas or electric?
4/30/2016 5:24:50 PM • Maytag Neptune... • Answered on Apr 30, 2016
0helpful
1answer

Upon putting the machine back together, the door somehow now does not fit when closing.

The cabinet make of racked while you were working on it. Loosen the screws and gentle press it to the side that is off and re tighten the screws.
4/3/2016 9:15:21 AM • Maytag Neptune... • Answered on Apr 03, 2016
0helpful
1answer

What does the E3 code mean?

This is what it means: Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving. (Locked, Hall Sensor fault). If you need additional help let me know
4/3/2016 9:02:59 AM • Maytag Neptune... • Answered on Apr 03, 2016
0answers
0helpful
1answer

Washer stopped at 27 minutes could not get it ti resart, unplugged an it is trying to reset itself.

Press "end of cycle" to get machine to normal. Then plug off the wall. Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too. Rate me pl.....if helped.
12/9/2015 2:36:11 PM • Maytag Neptune... • Answered on Dec 09, 2015
0helpful
1answer

Model #MAH6500AWW. Won't start. I hear 3 weird sounds in succession. Then a humming sound.

Check that the water input is wide open (security tap)
12/1/2015 9:47:55 AM • Maytag Neptune... • Answered on Dec 01, 2015
0helpful
1answer

Leaking from bottom

Common problems link. If you put in your model# there you will get more detailed results. Maytag Washer Leaking Water
11/28/2015 2:16:20 AM • Maytag Neptune... • Answered on Nov 28, 2015
0helpful
1answer

Water is coming out of the detergent dispenser

This is probably due to excess detergent blocking the feed into the machine, try removing the tray and washing it in the sink. If this works I would rinse it out every month or so, this could be done in the machine by not putting detergent in the dispenser and putting the machine on a short wash cycle. Hope this helps.
10/28/2015 4:39:39 AM • Maytag Neptune... • Answered on Oct 28, 2015
0helpful
1answer
0helpful
1answer

Ways to stop boot sealer from leaking

Hello. I need the model number AND the serial number to help you accurately. If this is the front loading Neptune, be aware--there are MANY service bulletins associated with it. Depending on the model/serial number, somewhere around 19 to 25 service bulletins exist. When there is a leak in the boot(also called a bellow, the rubber part that seals against the door glass), it must be replaced. Due to vibration/movement/water during agitate and spin, almost no type of adhesive will hold securely. People have tried to patch these parts but it always ends up leaking again after awhile. NOTE: Make sure the door glass is CLEAN at the rear(the area closest to the door itself where the seal is made with the bellow). If pet hair, hardened soap residue, almost any debris gets in-between the rubber seal area and the glass, water will weep through and drizzle down the front of the washer. Pet hair and almost any fibrous material will cause a wicking action that will cause leakage. I hope I helped you!
9/12/2015 5:14:34 AM • Maytag Neptune... • Answered on Sep 12, 2015
Not finding what you are looking for?
Maytag Neptune MAH6700A Front Load Washer Logo

123 questions posted

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Jessie Goss

Level 2 Expert

162 Answers

Sheldon Dedek

Level 3 Expert

912 Answers

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Neptune Maytag

  • Neptune Maytag

Most Popular Question

washer will not dispense softener rinse

  • Washing Machines
Loading...