20 Most Recent Norelco 7800XLCC Electric Shaver - Page 2 Questions & Answers

You will find the battery for model 7800XL at shaveroutlet.com. See link below

http://shaveroutlet.com/shaver-replacement-parts/shaver-replacement-battery-aa-nimh-p-108.html

Model 7800XL has 2 screws on the back. Remove the screws to take off the outer cover. You will then need to remove 3 more screws on the inner back cover. This inner cover has a tight seal and you will have to pry it up a bit to get it off. You can then access the battery and circuit board

Thanks for your question!
I'm sorry that you haven't received an answer yet.
The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...
Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.
Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

hi minglim, welocme to the forum!

Replacing a Norelco Shaver Battery Things You'll Need:Torx screwdriver set Rechargeable Ni-Cd AA battery 1)Slide up the sideburns trimmer on the shaver .2)Try the various torx head screwdriver sizes to find the fit for the two screws holding the top of the back shaver cover on. Unscrew the two screws that are under the sideburns trimmer that hold the back of the shaver on. On some Norelco shavers, the back will now slide off if you apply downward pressure on the shaver's back. Other Norelco shavers have one or two torx screws on the base of the back cover on the shaver; if so, unscrew them also. Place the screws in a safe place. 3)Take the back cover off the shaver. Some shavers may have a strap fastening the battery down. Unfasten the strap if there is one. Take out the battery. 4)Replace the old battery with a new rechargeable Ni-Cd AA battery. Re-fasten the battery holding strap if there was one. 5)Replace the back shaver cover and re-screw in all the torx screws,

something is jamming the heads from turning. the high pitched sound is the motor trying to turn but cant. if you are certain tht ll 3 blades turn freely inside their combs, the problem must be with he retainer that holds the blades into th frame. there are metal pieces on there that can get bent and interfere with the blades. If your retainer is damaged, you can get a new one at shaveroutlet.com

i get norleco saver when i want to stop it from workink it not stop and keep working whet can i do
thankes
eli
[email protected]

Return the shaver to the store from which you purchased from. It would appear that one or more of the Ni Cad batteries are no good and will not accept a charge. Have you attempt to plug the charger directly into the shaver? If not, try that and see if the shaver will run. Still your best move is to return the unit to the store as it is still under store return warranty. Dutchman

Question edited for clarity. Two questions merged to one. Duplicate question deleted, refresh page to see your question. some Norelco spares are available https://www.google.com/search?q=replacement+heads+for+my+old+Norelco+Electric+Razor+type+HP1122 ..

I see some that are offered on E Bay https://www.ebay.com/itm/404374101537?chn=ps

It is possible that your shaver does not turn on or move because it is dirty. There can be hair or dirt particles stuck inside it, causing the shaving heads to be blocked. To fix this problem, properly clean your shaver. If possible, remove the shaving head and clean your shaver from the inside as well.

https://www.manualslib.com/manual/125343/Philips-Norelco-8240xl.html#manual

It's true that Norelco does not sell parts for this unit, but you can buy a exact replacement for the pump motor here:https://www.amazon.com/dp/B0146XUE4I/ref=cm_sw_r_api_i_KGSBKR1BPW349RR3YRSB_0?psc=1.The only difference will be the length of the replacement motor shaft is too long, but this can be modified using a Dremel cut-off tool. Getting to the motor is a bit involved, but it is possible to do so without breaking anything. You'll need a T-8 driver and a small flat screw screw driver Begin by releasing the bottom, remove the fluid cartridge, and turn the unit upside down. Find and remove the (3) T-8 screws along the bottom perimeter. Next, use the small flat screwdriver or plastic pry bar to lift the outer case over the upper edge of the rear power supply socket and slide the outer case down. You'll also need to press the cartridge release button to clear the case Slip the outer case off the bottom. You'll need to twist it somewhat to clear the base. Now find and unplug the two side wire connectors (purple/white and orange/white wires) and slide the rear power supply connector off of the back of the unit, leaving it connected to the circuit board Now find and remove the (4) silver T-8 screws holding the base to the circuit board. Back the screws out only far enough to separate the base from the circuit board, leaving them attached to the black base so as to make it easier to reinstall later Gently separate the base from the circuit board. You will feel a bit of resistance as a hose separates from the base. Note where it attaches for later reinstallation. Now we need to remove the "legs" to gain access to the bottom of the pump. Place the separated vase upright and compress the springs to lock the legs in closed position. Note the two hooked ends sticking up. You will be using the small flat screwdriver to pry these towards the center. Open the "legs" by pressing the side button. Slide the flat screwdriver down the side of the base and use it to pry the hook so you can pull the leg out. You'll have to pull slightly on the bottom while doing this until you feel the hook release, and then you'll move the screwdriver to the second hook on this leg and repeat. Then move to the other leg and do the same. It takes a bit of practice but it'll eventually release. Be gentle. Separate the leg unit from the rest of the base. Be careful not to tangle or damage the coil springs. Set the legs and springs aside. Inspect the bottom of the pump. Gently pry the bottom cap off of the pump with your fingernails. Gently pry the impeller off the bottom of the pump motor shaft using a tiny screwdriver. Be careful not to damage the impeller. Turn the pump unit over. Use small screwdriver to gently pop loose the pump motor restraint (3 points) Lift the pump motor out of the housing. You can now clean the housing. Remove the two seals from the impeller end of the motor. You will transfer these to the replacement motor. Use soldering iron to remove the wires from the old motor and solder them to the new motor. Use a Dremel tool to shorten the shaft of the replacement motor to match the length of the old motor.Installation is the reverse of removal except I recommend saving reinstallation of the "legs" and springs for last - put everything else together first, including the outer case. Then line up the springs and legs and carefully press them together.

Was the polarity correct? Did you leave on to charge for a few hours. If yes to all that, then yes, the board has failed.

This model was made about 50 years ago. Blades have not been made for it for 30 years

ASK GOOGLE THE QUESTION

If the charger is like this, yes it is. Look on the inside where the plug pins are. If it is directly corded, it should be on the base. https://www.amazon.com/Charger-Philips-Norelco-HQ8505-Electric-Multigroom-Power-Supply/dp/B07M8W36RC/ref=pd_day0fbt_img_1/138-0807675-9832200?pd_rd_w=LWW3H&pf_rd_p=bcb8482a-3db5-4b0b-9f15-b86e24acdb00&pf_rd_r=CAC91S7MVDS8TZ6SFD19&pd_rd_r=e1199dac-6cdc-437c-98e8-d4b32633f980&pd_rd_wg=Mj6Vn&pd_rd_i=B07M8W36RC&psc=1 More information https://www.google.com/search?q=Norelco+shaver+4805+XL+specs ..

yes, model 825RX has dual voltage capability

https://www.msn.com/en-us/Lifestyle/rf-buying-guides/best-norelco-shavers-reviews- BEST NORESCO SHAVERS

The part comes complete as motor and gears.https://philips.encompass.com/model/NOR8140XL..

If your Norelco has a dry/wet shave feature, get your skin damp and then apply a thin layer of shaving cream, gel or foam. Press the "on/off" button once to turn on the shaver. Run the shaver over your cheeks and jawline in both circular and straight motions, working against the grain, or growth, of the hair. So I wouldn't put water in the top so you do not damage the product.

https://www.youtube.com/watch?time_continue=36&v=2oAnLpvdYqQ