20 Most Recent Akai PTH5498 54" Rear Projection HDTV-Ready Television - Page 3 Questions & Answers

maybe one of the wires came out inside

try www.retrevo.com they should have the user manual free if you type the model number in the search box.

Any colors R,G,B out of alignment the convergence board are dead.The tv convergencce board must have it 2 STK convergencce ICS,and some or all it resistors be replaced to solved the convergence problems.The shop will cost u $300-350 for parts and labors.

Did you replace the 3.9 ohm fusible resistors? Often several of those will blow with the old ICs.

Projection TV sets are known to have two common problems. The first problem that is common to these sets is convergence failure. When this happens the TV will usually look 3D, Wavy/Distorted, etc. It may also shutdown and blink an error code.

The second common problem with Projection TV sets is dull video, halos around objects, white looking video, or red overpowers the screen. This is commonly caused by the fluid in the lens being clouded overs. To get fixed either call in a local TV repair company or goto sites such as Tv Repair Kits to get a repair kit with instructions. Here is there link.

http://www.tvrepairkits.com/xcart/home.php?partner=papa1dude

They have put together complete kits for most models that include the parts, step by step photo instructions, repair assistance, etc.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems.






Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on - TV may also make a chirping noise.

Here are some photos of convergence problems.





Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony, Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer, Hitachi,Mitsubishi,Zenith and others.
You can get more information and a DIY convergenece repair kit with instructions from the link below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2 - Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

The most likely cause is shorted convergence chips and possibly a few pico fuses.

These sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the picture to look normal. This is called convergence.

When its out of alignment the video will look 3-D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired. Convergence problems are very common on all Projection TV sets including Sony,Samsung,JVC,Philip Magnavox,Panasonic,Akai,Pioneer Hitachi,Mitsubishi,Zenith and others.
You can get a convergenece repair kit with instructions from the links below.

Here are some of the most common problems with these sets...

Problem #1) Convergence

Yours may have one or more of the following symptoms...

*Screen Looks 3-D
*Colors wont align
*Screen may look distorted or warped
*No Audio/Video - TV Shuts down - May also make a constant chirping sound

Problem #2
Another common problem is dull or washed out video.

Your set may have one or more of the following symptoms....

*Dull looking picture
*White looking picture
*Halos around objects
*Red/Orange looking picture

You can see some more examples and find a fix here http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

This called a convergence error. Definitely a service shop issue. Repairs can run $200 - $400+ depending on service call, parts cost, delivery, etc. Can even be more for some sets. Get a quote.

· http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
· http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html

dont know wot the problem is there mate, hope this helps!

The convergence amps have most likely failed and taken with them the +/- 30v line. Your unit takes two STK392-040 Sanyo built Ics at board location Icz103 and Icz104 and usually one or more pico fuses and some low ohm resistors. F1018 sometimes opens due to stress but generally it's just the two 6.3 amp pico fuses and if they have opened I strongly recommend replacing them with a 6.3 amp slo-blo pico.
The low ohm resistors at RZ147, RZ146 usually show signs of heat stress and may even be burned beyond recognition. Testing at that point is almost unnecessary but will confirm their change in value. Almost always they need to be replaced.
A quality shop will have this unit back on its feet in no time - faster if they have the parts in-stock, which you might ask about when you shop around for a good repair facility.
Have a great day!
Bill

Try it with a HDMI cable,It have better result in signal wise,Bluray mostly in High Def.

This is a common problem. Its called a convergence failure.

Problem #1) Convergence

Symptoms:

• Screen Looks 3D
• Colors wont align
• Video may look distorted

You can see some examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Convergence board is dead.Go to Tv repair World.com buy a new convergence board replaced the board will solved ur problems.Samsung/Akai use same convergence board.

If you dont feel comfortable goto www.TvRepairKits.com. They have put together DIY kits that include all the parts and step by step photo instructions. They also provide support in case you have any quesitosn during the repair.

You may want to check the terminals and the wires if there is a short somewhere. You can do this by physically inspecting the internal for conductors touching each other or similar to checking continuity only this time is continuity from certain points to the ground.

I turned on the tv this morning it ran about 10 min.iheard a click the screen went black and will not come back on

Hello:

Yes is is your convergence IC's. One has gone bad, but consider replacing both of them because if one has gone bad then the other is not far behind. They are located on the middle board of your set. They are mounted on a large heatsink, the part # should be STK-392-040. Replace these and your set will work fine again.