20 Most Recent Candy AQUA1000T Front Load Questions & Answers

hi there, it sounds as if your drive belt is loose or broken. when you put you ear to the machine can you hear the motor running, if the motor runs but nothing else happens its a sure sign that the belt is gone. whilst you might look silly doing this, it may prevent you opening the machine up to replace the belt if you not have to.
thanks iain

Hi from retired Englishman in SW France,

Sorry but I do not know your particular machine BUT I would suggest as a first step that you clean the drain motor lint tray/filter. So many 'faults' are caused by blocked filters. The motor is unable to drain all of the water in the allotted time.
If you are unsure where the filter is, it is normally behind the front lower (kick) panel (or in some machines at the rear in an awkward position!) and held in by a round cover/knob.

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!

It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. If it doesn't work then the motor is malfunctioning!

Hope the filter is the problem and good luck!
John C

Hi from retired Englishman in SW France,

Here is my generic 'standard' document ;-0)
It's quicker than typing it every time and I hope it helps!
----------------------------------------------------------------------------------------------------------------------------------------
Sorry but I do not know your particular machine BUT it is normally behind the front lower (kick) panel (or for some washers in a more awkward position at the back) and held in by a round cover/knob.

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!

It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. If it doesn't work then the motor is malfunctioning!
----------------------------------------------------------------------------------------------------------------------------------------
Good luck!
John C

Try plugging or unplugging the Washing Machine






I hope this works



THANKS

this machine has a float problem and needs to be taken apart so a service rep should handle this one

http://service.candy-domestic.co.uk/manuals/pdfs/AQUA%201000T.pdf
I have found you a user manual, to download and read, this should help you resolve your issue.

Check water level switch. may be the small tube that carries water to the switch assembley. Either clogged or air trapped. Pull it re fix it. it should become ok.

Before that fill the m/c with water manually. Switch off power supply to the washer and attempt. ( Safety precaution)

Assuming you have located the filter at the bottom front of washer, you unscrew it anti-clockwise to remove and clean.
If there is a small screw in the filter handle, then unscrew it first, before removing filter.
Please rate my solution.
Thankyou.

this sounds like the conditioner solenoid, this is the cold water valve that works as the final rinse is suppose to work, just before the final spin, check valve connections for open circuit electrically, work safe unplug from power supply first, if i have helped please rate me

Are you sure that this not is the cooldown phase of the mainwash? Most frontloaders have this feature.

you have tried all ways its better to go to the mechanic it can help out more if he can find out some related problem
Thanx

Candy Washing Machine

1. Push and hold the FIRST Option Button with LED top right.
2. Turn the Program's Selector Knob 2 clicks clockwise.
3. After about 5 seconds, release the FIRST Option Button.
4. If the previous procedure was correctly carried out, all LEDs are turned ON simultaneously.
5. Press the START/PAUSE Button to start the self test mode

the pump is blocked up or the filter once you take the blockage you need to reset the machine too do this turn off the mains power press and hold usually the start pause or menu button and turn the mains on wait a few seconds and let go should clear the fault detection if it is the filter or a blocked bad pump and its clear then the machine will reset

Error code E11?? See error codes here: How to Understand Hoover and Candy Washing Machine Error Codes

https://www.youtube.com/watch?v=-Ugge61yrHE Has to do with the motor

I have always found that my Candy refuses to function at times, especially if I have tried to set it with wet hands. Do a Master Reset. Switch the circuit breaker off. Wait for 60 seconds. Turn it back on. Open and close the door 6 times within 12 seconds. I know it sounds mad but it works.