20 Most Recent Denon AVR-1706 Receiver - Page 8 Questions & Answers

This is a normal condition when a capacitor or more on the power board has failed, this is a common issue however I can not assure you that this is your issue. I also advise against opening it up to work on it but if you did you want to locate any bulging or obviously distressed capacitors.(oozing liquid, extra plum-stolen, smelly or melted parts you can also look for weak spider joint as the cold air makes us keep the heat on more and along with prolonged use can weaken solider joint in some electronics good luck. https://www.6ya.com/mr.mike

“Is it possible to program a brookstone universal touch screen remote to the receiver without the factory remote?” No need to program a brookstone universal touch screen remote to the receiver. “If so how please?”Just google 'denon app download' will get help. Try to download "denon app for Android" (denon remote app) to control the amp .

check SMPS of Denon AVR X3300W located at AC in.
The voltage 5.26V may be
down. If current protect ,
check ALL components of
power amp OR replace them ALL.

I have the same issue with my DENON receiver. I know that there must be a setting in some menu someplace. But how can you read the menu when the display is too damn dim, right? I have searched through the buttons on the remote and pressed all of them after changing the batteries twice. They are either unsmart or they don';t care. Any way it sucks

Denon PMA 250SE does not have a RIAA phono preamp.for some info about these preamp and details here;Phonopreamps.com Home PageNote: Choose a better quality regulated power supply,for these preamps. Although an updated turntable with USB can be used without the need of such RIAA phono preamp.

How do I get it on stand by as without the receiver being on standby cannot get the Denon instruction on my TV screen. It is impossibe to do so. When in standby mode, CPU voltage supply is shorted to ground. CPU shuts down. Without receiving any signals from CPU, both HDMI input and decoder do not work. They work only working CPU is fully awake.

Try and unplug all the cables from the unit and see if it still turns off with nothing connected. If not, connect one speaker at a time to see if there is a short

Check the speaker terminals. If they are crossed. You may have activated the overload circuits. also you may have too high ohm speakers. Connect 8 ohm speaker and try again. Make sure wires are correct + to + and - to - on both ends. If you have all this it should work. Good luck.

Not much to set up - make sure the turntable is level and stable and the tonearm adjusted to the correct playing weight for the cartridge/stylus and then connect the turntable to a suitable RIAA corrected preamp input - low impedance high sensitivity for magnetic cartridge and high impedance low sensitivity for ceramic or piezo cartridge. The speakers are best placed far enough apart for good stereo separation and on a substrate that doesn't resonate, if necessary placing them on something like concrete paving slabs or fitting them with pointed feet to bite through carpet.

Sounds like a new remote would be cheaper than repairing it. The old one could have been dropped or even had water or coffee spilled over it.

Hello, Turn off the power using. Press power simultaneously pressing TUNER PRE SET CH+ and TUNER PRE SET CH- Remove from finger from the two button when initialize the dispaly. Before restore the all setting save function of the web control.

The digital out is either a coax (TV cable) you screw on and connect to the same type connector on the receiver or it is a small square connector that requires a fiber optic cable designed for this.

The unit's manual will show you.

https://www.manualslib.com/manual/38369/Denon-Avr-587.html

Hello There is always a constant 5v for the device to go to standby.and power on when you press the power button . This flashing is not to reset the device it shows that there is a problem with power supply. the regulators are burned or over voltage ... it needs service . hope this helps good luck

Assuming you are not a trained repair tech, I'd suggest you take the unit to an authorized Denon repair center. Ask for an estimate, hopefully no charge, so you can decide whether or not to pay to have it repaired. Do not attempt to repair it yourself.

Check the front of the unit ,most have a small hole, using a paperclip as a probe on the gear with a to and fro movement you will be able to work the draw open.

Most amps shut down due to a fault in the power amp section. Often caused by bad speaker, cables or connections. Another cause is a shorted output device in the power amp.

Hi! Please check the manual to Denon AVR-1082 Hope it will help you Denon AVR 1082 User Manual Page 15 of 42

The Denon AVR-887 does not support ARC (audio return channel) on the HDMI output. You can find the specifications for the AVR-887 in the manual. ManualsLib has the manual here: https://www.manualslib.com/manual/38390/Denon-Avr-887.html . The specifications are listed here: https://www.manualslib.com/manual/38390/Denon-Avr-887.html?page=77#manual . The page with the monitor connection is https://www.manualslib.com/manual/38390/Denon-Avr-887.html?page=22#manual . I hope this helps. Cindy Wells